Mitsubishi Outlander GS45X. Manual — part 1086
DOOR
TSB Revision
BODY
42A-147
INSPECTION
M1423006000753
DOOR SWITCH CHECK
Switch position Terminal
number
Normal
value
Release (ON)
1
− Ground, 2 −
Ground, 3
−
Ground
Continuity
exists (2
Ω or
less)
Depressed
(OFF)
1
− Ground, 2 −
Ground, 3
−
Ground
Open circuit
AC211414AB
1
2
3
DOOR
TSB Revision
BODY
42A-148
DOOR GLASS AND REGULATOR
REMOVAL AND INSTALLATION
M1429001301299
Required Special Tool:
• MB990480: Window Glass Holder
Post-installation operation
• Door window glass adjustment (Refer to
AC703242
1
2
3
AC
2
<Front door>
4.0 ± 2.0 N·m
35 ± 17 in-lb
4.0 ± 2.0 N·m
35 ± 17 in-lb
7.5 ± 1.5 N·m
66 ± 13 in-lb
7.5 ± 1.5 N·m
66 ± 13 in-lb
Door window glass assembly
removal steps
•
Door trim assembly (Refer to
GROUP 52A, Door Trim
.)
•
Waterproof film, belt line molding,
belt line weatherstrip inner, and
speaker bracket (Refer to
1.
Door window glass assembly
Power window regulator
assembly removal steps
>>A<<
•
Post-installation operation check
<Driver’s side only>
•
Door trim assembly (Refer to
GROUP 52A, Door Trim
.)
•
Waterproof film and speaker
bracket (Refer to
<<A>>
2.
Power window regulator assembly
3.
Power window motor
DOOR
TSB Revision
BODY
42A-149
Required Special Tool:
• MB990480: Window Glass Holder
AC703241
2
1
3
AC
2
<Rear door>
4.0 ± 2.0 N·m
35 ± 17 in-lb
7.5 ± 1.5 N·m
66 ± 13 in-lb
Door window glass assembly
removal steps
•
Door trim assembly (Refer to
GROUP 52A, Door Trim
.)
•
Waterproof film, belt line molding,
belt line weatherstrip inner, door
window glass channel, and speaker
bracket (Refer to
•
Door latch assembly (Refer to
1.
Door window glass assembly
Power window regulator
assembly removal steps
•
Door trim assembly (Refer to
GROUP 52A, Door Trim
.)
•
Waterproof film and speaker
bracket (Refer to
<<A>>
2.
Power window regulator assembly
3.
Power window motor
AC703245
1
2
3
4
5
6
AC
<Front door>
<Rear door>
DOOR
TSB Revision
BODY
42A-150
REMOVAL SERVICE POINT
.
<<A>> POWER WINDOW REGULATOR REMOVAL
1. Remove the door window glass installation bolts.
CAUTION
If tinting film is adhered to the door window glass, attach
special tool MB990480 to the outside of the glass to pre-
vent the film from peeling off.
2. Lift the door window glass, and attach special tool
MB990480 to the glass as shown to prevent the glass from
falling.
3. Remove the power window regulator.
INSTALLATION SERVICE POINT
.
>>A<< POST-INSTALLATION OPERATION CHECK
<DRIVER'S SIDE ONLY>
When the following procedures are carried out, carry out the
learning procedures of the power window fully closed position
(Refer to
• Power window regulator removal or replacement
• Power window switch removal or replacement
INSPECTION
M1429001400884
POWER WINDOW SWITCH CONTINUITY CHECK
.
Power window switch <Front
door> removal step
>>A<<
•
Post-installation operation check
<Driver’s side only>
•
Door trim assembly (Refer to
GROUP 52A, Door Trim
.)
1.
Power window switch panel
assembly
2.
Power window switch panel
3.
Power window main switch
<Driver's side>, power window sub
switch <Front passenger's side>
Power window sub switch <Rear
door> removal step
•
Door trim assembly (Refer to
GROUP 52A, Door Trim
.)
4.
Power window switch panel
assembly
5.
Power window switch panel
6.
Power window sub switch
AC703243AB
MB990480
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст