Mitsubishi Outlander GS45X. Manual — part 1085
DOOR
TSB Revision
BODY
42A-143
DOOR INSIDE HANDLE LOCK KNOB STROKE
CHECK
1. Remove the door trim assembly (Refer to GROUP 52A
−
Door Trim
2. Check that the stroke of the door inside handle lock knob
meets the standard value.
Standard value (B): 13.7
− 15.0 mm (0.54 − 0.59 inch)
[Target value: 14.7 mm (0.58 inch)]
3. If it is outside the standard value, adjust the stroke of the
inside handle lock knob by using the outer cable end, which
connects the inside handle lock knob to the inside lock
cable.
AC605584
A
B
AC
A
Section A – A
AC605585 AC
Clip
Outer cable end
Inside lock
cable
Door inside handle
DOOR
TSB Revision
BODY
42A-144
CUSTOMIZATION FUNCTION
M1429007800921
Using the ETACS system of scan tool MB991958,
the following functions can be programmed. The pro-
grammed information is held even when the battery
is disconnected.
Adjustment
item (scan tool
MB991958
M.U.T.-III
display)
Adjustment item
Adjusting contents
(scan tool MB991958
display)
Adjusting contents
Door unlock
mode
Adjustment of
power door locks
with selective
unlocking
All doors unlock
Without function: The first operation of
keyless entry system or unlock operation
by KOS unlocks all doors.
Dr door unlock
With function: The first operation of
keyless entry system or unlock operation
by KOS unlocks the driver's door only, and
the second unlock operation within 2
seconds after that unlocks all doors. (initial
condition)
Auto door
unlock
Adjustment of the
auto door unlock
function
Disabled
Without function (initial condition).
Always (P pos)
With function: Operates when the shift
lever or the selector lever is moved to the
P position.
Always (Lock pos)
With function: Operates when the ignition
switch is moved to the LOCK (OFF)
position.
DOOR
TSB Revision
BODY
42A-145
DOOR ASSEMBLY
REMOVAL AND INSTALLATION
M1423002200841
Post-installation operation
• Door adjustment (Refer to
.)
AC703238
6, 7
1
2
3
4
6
7
9
8
10
AB
26 ± 6 N·m
19 ± 5 ft-lb
26 ± 6 N·m
19 ± 5 ft-lb
25 ± 4 N·m
19 ± 3 ft-lb
20 ± 5 N·m
15 ± 3 ft-lb
4.0 ± 2.0 N·m
35 ± 17 in-lb
5.0 ± 1.0 N·m
44 ± 9 in-lb
5
<Front door>
Damper removal
1.
Damper
Door assembly and front door
hinge removal steps
•
Front scuff plate, cowl side trim
(Refer to GROUP 52A - Interior
Trim
.)
2.
Wiring harness connector
connection
3.
Door check connecting bolt
4.
Door assembly
•
Side air dams (Refer to GROUP 51,
Side Air Dams
P.51-20
.)
5.
Fender rear protector
6.
Front door upper hinge
7.
Front door lower hinge
Striker removal steps
>>A<<
8.
Striker
9.
Striker shim
Door switch removal
10. Door switch
Door assembly and front door
hinge removal steps (Continued)
DOOR
TSB Revision
BODY
42A-146
INSTALLATION SERVICE POINT
.
>>A<< STRIKER INSTALLATION
Install the striker so that the striker center does not deviate
more than
±1.5 mm (0.06 inch) from the latch center.
AC703239
5, 6
1
2
3
4
5
6
7
8
9
AB
<Rear door>
26 ± 6 N·m
19 ± 5 ft-lb
26 ± 6 N·m
19 ± 5 ft-lb
25 ± 4 N·m
19 ± 3 ft-lb
18 ± 7 N·m
13 ± 5 ft-lb
18 ± 7 N·m
13 ± 5 ft-lb
20 ± 5 N·m
15 ± 3 ft-lb
5.0 ± 1.0 N·m
44 ± 9 in-lb
10
11
Damper removal
1.
Damper
Door assembly removal steps
2.
Wiring harness connector
connection
3.
Door check connecting bolt
4.
Door assembly
Rear door hinge removal steps
•
Center pillar trim (Refer to GROUP
52A, Interior Trim
.)
5.
Rear door upper hinge
6.
Rear door lower hinge
Striker removal steps
>>A<<
7.
Striker
8.
Striker shim
Door switch removal
9.
Door switch
Rear door catch removal
10. Rear door catch
Rear door lock hook removal
11. Rear door lock hook
AC703240AB
+1.5 mm
(0.06 in)
-1.5 mm
(0.06 in)
Striker center
Striker
Latch center
Latch
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст