Mitsubishi Outlander GS45X. Manual — part 765
INJECTOR
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <2.4L ENGINE>
13A-883
>>D<< FUEL INJECTOR SUPPORT
INSTALLATION
Install the fuel injector support to the fuel injector groove and
fuel rail flange, and fix the fuel injector assembly and fuel rail.
.
>>E<< FUEL RAIL AND FUEL INJECTOR
ASSEMBLY/BRACKET/INJECTOR PROTECTOR
REAR INSTALLATION
CAUTION
When applying the engine oil, make sure not to allow the
engine oil to enter the intake manifold inside.
1. Apply a small amount of new engine oil to the O-ring at the
end of fuel injector assembly.
CAUTION
When installing the fuel rail and fuel injector assembly to
the intake manifold, pay attention to avoid damage to the
O-ring at the end of the fuel injector assembly.
2. Install the fuel rail and fuel injector assembly to the intake
manifold.
3. Install the bracket and injector protector rear.
4. Loosen the intake manifold mounting bolts and nuts (Bolts
and nuts 1, 2, 3, and 9 shown in the figure).
5. Remove the EGR valve (Refer to GROUP 17, Emission
Control
− Exhaust Gas Recirculation (EGR) Valve <2.4L
Engine>
).
6. Loosen the EGR valve support and intake manifold coupling
bolts (Refer to GROUP 17, Emission Control
− Exhaust Gas
Recirculation (EGR) Valve <2.4L Engine>
).
7. Loosen the intake manifold stay mounting bolts (Refer to
GROUP 15, Intake Manifold <2.4L Engine>
).
8. Temporarily tighten the mounting bolts and nuts of the inlet
manifold, bracket, fuel rail and injector protector rear to the
specified torque in the order of number shown in the figure.
Tightening torque: 3.5
± 1.5 N⋅m (31 ± 13 in-lb)
9. Tighten the mounting bolts and nuts of the inlet manifold,
bracket, fuel rail and injector protector rear to the specified
torque in the order of number shown in the figure again.
Tightening torque: 20
± 2 N⋅m (15 ± 1 ft-lb)
10.Tighten the inlet manifold stay mounting bolts to the
specified torque (Refer to GROUP 15, Intake Manifold <2.4L
Engine>
).
AC312109
AC
Fuel rail brim
Fuel injector
support
Fuel injector
groove
AC507953AB
10
3
5
7
1
6
4
2
9
8
INJECTOR
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <2.4L ENGINE>
13A-884
Tightening torque: 20
± 2 N⋅m (15 ± 1 ft-lb)
11.Tighten the EGR valve support and intake manifold coupling
bolts to the specified torque (Refer to GROUP 17, Emission
Control
− Exhaust Gas Recirculation (EGR) Valve <2.4L
Engine>
).
Tightening torque: 20
± 2 N⋅m (15 ± 1 ft-lb)
12.Install the EGR valve (Refer to GROUP 17, Emission
Control
− Exhaust Gas Recirculation (EGR) Valve <2.4L
Engine>
).
.
>>F<< FUEL HIGH-PRESSURE HOSE
CONNECTION
1. Pull up the retainer of fuel high-pressure hose to unlock
before installing.
2. Securely insert the fuel rail stopper into the fuel
high-pressure hose connector groove to install the fuel
high-pressure hose to the fuel rail.
CAUTION
• When pushing in the retainer of the fuel high-pressure
hose connector, pay attention to avoid damage to the
retainer.
• After the installation of the fuel high-pressure hose,
slightly pull the fuel high-pressure hose to check that it
is connected securely. At this time, also check that
there is approximately 1 mm (0.04inch) play.
3. Push in the retainer of the fuel high-pressure hose
connector to lock the fuel high-pressure hose and fuel rail.
AC606113
Fuel high-pressure
hose
Retainer
AB
AC506794 AB
Fuel high-pressure
hose
Fuel rail
Retainer
Stopper
THROTTLE BODY ASSEMBLY
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <2.4L ENGINE>
13A-885
THROTTLE BODY ASSEMBLY
REMOVAL AND INSTALLATION
M1131007702261
CAUTION
• When the throttle body assembly replacement is performed, use scan tool MB991958 to initialize
the learning value (Refer to GROUP 00, Precautions Before Service
− Initialization Procedure for
Learning Value in MFI Engine
P.00-53
).
• Never loosen the screw fixing the throttle body assembly resin cover. If the screw is loosened, the
sensor incorporated in the resin cover is misaligned and the throttle body assembly does not
work normally.
Pre-removal operation
• Engine Upper Cover Removal (Refer to GROUP 11A,
Camshaft
• Engine Coolant Draining (Refer to GROUP 14, On-vehicle
Service
− Engine Coolant Replacement
P.14-26
).
• Air Cleaner Intake Hose Removal (Refer to GROUP 15,
Air Cleaner <2.4L Engine>
).
Post-installation operation
• Air Cleaner Intake Hose Installation (Refer to GROUP 15,
Air Cleaner <2.4L Engine>
).
• Engine Coolant Refilling (Refer to GROUP 14, On-vehicle
Service
− Engine Coolant Replacement
P.14-26
).
• Engine Upper Cover Installation (Refer to GROUP 11A,
Camshaft
).
AC609824AB
2
4
9
1
N
5
7
8
9.5 ± 2.5 N·m
88 ± 22 in-lb
3
6
9.5 ± 2.5 N·m
88 ± 22 in-lb
20 ± 2 N·m
15 ± 1 ft-lb
Removal steps
>>
B
<<
•
Initialization operation (only at
installation)
1.
Throttle body assembly connector
connection
2.
Control wiring harness clip
connection
3.
Battery wiring harness clamp
connection
4.
Throttle body water feed hose
connection
5.
Throttle body water return hose
connection
6.
Throttle body stay
7.
Throttle body wiring harness
connector bracket
8.
Throttle body assembly
>>
A
9.
Throttle body gasket
Removal steps (Continued)
THROTTLE BODY ASSEMBLY
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <2.4L ENGINE>
13A-886
INSTALLATION SERVICE POINTS
.
>>A<< THROTTLE BODY GASKET INSTALLA-
TION
Fit the throttle body gasket in the intake manifold groove
securely with neither twisting nor damage given.
.
>>B<< INITIALIZATION OPERATION
Turn the ignition switch to the "ON" position and then to
"LOCK" (OFF) position and hold it for at least 10 seconds.
AC506797
AC
Intake
manifold
Throttle body
gasket
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст