Mitsubishi Outlander GS45X. Manual — part 64

REAR COMBINATION LIGHT

TSB Revision

CHASSIS ELECTRICAL

54A-253

STEP 8. Check ETACS-ECU connectors C-312 for loose,
corroded or damaged terminals, or terminals pushed back
in the connector.
Q: Is ETACS-ECU connectors C-312 in good condition?

YES : Go to Step 9.
NO : Repair the damaged parts.

STEP 9. Check the battery power supply circuit to the
ETACS-ECU. Measure the voltage at ETACS-ECU
connector C-312.
(1) Disconnect connector measure the voltage available at the

wiring harness side of the connector.

(2) Disconnecting the ETACS-ECU connector C-312.
(3) Stoplight switch: ON
(4) Measure the voltage between ETACS-ECU connector

C-312 terminal No. 16 and the body ground.

• The voltage should measure approximately 12 volts

(battery positive voltage).

Q: Is the measured voltage approximately 12 volts (battery

positive voltage)?
YES : Go to Step 11.
NO : Go to Step 10.

STEP 10. Check the wiring harness between ETACS-ECU
connector C-312 (terminal No. 16) and stoplight relay
connector C-133 (terminal No. 2).

• Check the signal line for short circuit.

Q: Is the wiring harness between ETACS-ECU connector

C-312 (terminal No. 16) and stoplight relay connector
C-133 (terminal No. 2) in good condition?
YES : Go to Step 11.
NO : Repair the wiring harness.

STEP 11. Check the wiring harness between stoplight relay
connector C-133 (terminal No. 4) and intermediate
connector C-131 (terminal No. 9).
Check the communication line for open or short circuit.
Q: Is the wiring harness between stoplight relay connector

C-133 (terminal No. 4) and intermediate connector C-131
(terminal No. 9) in good condition?
YES : Go to Step 12.
NO : Repair the wiring harness.

AC608254EX

Harness side: C-312

REAR COMBINATION LIGHT

TSB Revision

CHASSIS ELECTRICAL

54A-254

STEP 12. Retest the system
Check that the stoplight illuminates normally.
Q: Does the stoplight relay work normally?

YES : The trouble can be an intermittent malfunction (Refer

to GROUP 00

− How to use

Troubleshooting/inspection Service Points

− How to

Cope with Intermittent Malfunction

P.00-15

).

NO : Replace the stoplight relay.

REAR COMBINATION LIGHT REMOVAL AND INSTALLATION

M1541402200239

AC703021AB

5

1.2 ± 0.7 N·m
11 ± 6 in-lb

4.5 ± 1.5 N·m
40 ± 3 in-lb

4

2

9

6

3

1

12

11

10

8

7

Removal Steps

1.

Rear combination light assembly

2.

Rear combination light unit

3.

Socket

4.

Bulb

5.

Grommet

6.

Liftgate cover garnish (Refer to
GROUP 52A

− Liftgate Trim

P.52A-14

)

7.

Taillight assembly

8.

Gasket

9.

Taillight unit

10. Socket
11. Bulb
12. Gasket

Removal Steps (Continued)

FOG LIGHT

TSB Revision

CHASSIS ELECTRICAL

54A-255

FOG LIGHT

SERVICE SPECIFICATIONS

M1540400900187

SPECIAL TOOLS

M1540401800309

Item

Standard value

Limit

Fog light aiming (cutoff line direction) [at 7.62
m (25.0 ft)]

The horizontal line 153.0
mm (6.02 inches) (1.15
degrees angle) below the
horizontal line (H)

−

Fog light aiming (vertical direction) [at 7.62 m
(25.0 ft)]

−

Area from 53.2 mm (2.09
inches) (0.4 degrees angle)
above the cutoff line to 99.8 mm
(3.93 inches) (0.75 degrees
angle) below the cutoff line

Fog light aiming (horizontal direction) [at 7.62
m (25.0 ft)]

−

Vertical line (V)

± 599.7 mm (±

23.6 inches) (

± 4.5 degrees

angle).

Tool

Tool number and
name

Supersession

Application

MB990784
Ornament remover

General service tool

Removal of fog light bezel

MB991223

a. MB991219
b. MB991220
c. MB991221
d. MB991222

Harness set

a. Test harness
b. LED harness
c. LED harness

adaptor

d. Probe

General service tools Continuity check and voltage

measurement at harness wire or
connector

a. Connector pin contact

pressure inspection

b. Power circuit inspection
c. Power circuit inspection
d. Commercial tester connection

MB990784

MB991223

a

d

c

b

DO NOT USE

BA

FOG LIGHT

TSB Revision

CHASSIS ELECTRICAL

54A-256

DIAGNOSIS

STANDARD FLOW OF DIAGNOSTIC TROUBLESHOOTING

M1540401700153

Refer to GROUP 00

− Contents of troubleshooting

P.00-7

.

MB991958

a. MB991824
b. MB991827
c. MB991910
d. MB991911
e. MB991914
f. MB991825
g. MB991826

M.U.T.-III sub
assembly

a. Vehicle

communication
interface (V.C.I.)

b. M.U.T.-III USB

cable

c. M.U.T.-III main

harness A
(Vehicles with
CAN
communication
system)

d. M.U.T.-III main

harness B
(Vehicles without
CAN
communication
system)

e. M.U.T.-III main

harness C (for
Chrysler models
only)

f. M.U.T.-III

measurement
adapter

g. M.U.T.-III trigger

harness

MB991824-KIT
NOTE: G: MB991826
M.U.T.-III Trigger
Harness is not
necessary when
pushing V.C.I. ENTER
key.

CAUTION

M.U.T.-III main harness B
(MB991911) should be used.
M.U.T.-III main harness A and C
should not be used for this
vehicle.
Diagnostic code, service data and
actuator test check.

MB992006
Extra fine probe

−

Continuity check and voltage
measurement at harness wire or
connector.

Tool

Tool number and
name

Supersession

Application

MB991910

MB991826

MB991958

MB991911

MB991914

MB991824

MB991827

MB991825

DO NOT USE

a

b

c

d

e

f

g

DO NOT USE

MB992006