Mitsubishi Outlander GS45X. Manual — part 1345
SPECIFICATIONS
TSB Revision
EXTERIOR
51-3
SPECIFICATIONS
SERVICE SPECIFICATIONS
M1511000301470
ADHESIVES
M1511000502251
LUBRICANT
M1511000400117
Item
Standard value
Stop position of the windshield wiper arm/blade assembly mm (in)
φ 2 marking ± 5(0.20)
Stop position of rear wiper arm and blade assembly (Distance from the
wiper blade to the ceramic line on the liftgate glass) mm (in)
0 to 20(0.79) from the ceramic
line
Heated door mirror resistance value ohm
7.2
± 1.4 at 25 °C (77°F)
Item
Specifications
Front and rear three-diamond mark
Double-sided tape: Generic products
0.8 mm (0.03 in) thickness
Clip D for roof drip molding
Double-sided tape: Generic products
10 mm (0.39 in) width and 30 mm (1.18 in) thickness
Side air dam
Double-sided tape: Generic products
4.0 mm (0.16 in) width and 1.2 mm (0.05 in)
thickness
Rear roof garnish
Double-sided tape: Generic products
10 mm (0.39 in) width and 1.2 mm (0.05 in)
thickness
Liftgate molding (attached on tailgate garnish)
<Some models>
Double-sided tape: Generic products
A: 10 mm (0.39 in) width and 1.2 mm (0.05 in)
thickness
B,C: 1.2 mm (0.05 in) thickness
Adhesive and dirt remover
3M
™ AAD Part number 8906
Item
Specified lubricant
Quantity
Wiper motor link rod
Contact joint between
link rod and wiper motor
link plate
Multipurpose grease SAE J310,
NLGI No.1(mineral oil + Li) or
equivalent
As required
FRONT BUMPER ASSEMBLY
TSB Revision
EXTERIOR
51-4
FRONT BUMPER ASSEMBLY
REMOVAL AND INSTALLATION
M1511001401942
Pre-removal and post-installation operation
• Headlight support panel cover removal and installation
(Refer to
.)
• Engine room under cover front removal and installation
(Refer to
• Splash shield removal and installation (Refer to GROUP
42A, Splash Shield
AC901081
1
2
AC
6
1
1
1
1
6
5
4
3
3
2
2
3
C
C
C
C
D
A
A
B
B
B
B
Section A – A
Section B – B
Section C – C
Section D – D
Front end cross member
Headlight
support panel
Headlight support
upper panel
Front end
cross member
Engine room under cover front
Front fender
Claw
Screw
Clip
Bolt
Boss
Front fender
D
5.0 ± 2.0 N·m
45 ± 17 in-lb
20 ± 5 N·m
15 ± 3 ft-lb
4.0 ± 2.0 N·m
35 ± 17 in-lb
9.5 ± 3.5 N·m
85 ± 31 in-lb
20 ± 5 N·m
15 ± 3 ft-lb
4.0 ± 2.0 N·m
35 ± 17 in-lb
Removal steps
•
Fog light connector connection
<Vehicles with fog light>
1.
Front bumper assembly
2.
Front bumper side bracket
•
Ambient temperature sensor (Refer
to Group 55A, Ambient
Temperature Sensor
3.
Headlight bracket
4.
Front end panel guide
•
Horn (Refer to Group 54A, Horn
)
•
Front harness
5.
Front bumper reinforcement
6.
Bumper lower bracket
Removal steps (Continued)
FRONT BUMPER ASSEMBLY
TSB Revision
EXTERIOR
51-5
DISASSEMBLY AND REASSEMBLY
M1511001602198
AC901144
4
11
14
16
15
13
3
1
8
AB
9
7
6
7
9
14,15
14,15
14,15
16
16
16
4
Claw
Boss
7
Claw
Claw
8
9
A
A
B
C
B
C
Section A – A
Section B – B
Section C – C
12
5
10
2
N
16
4
: Claw positions
0.9 ± 0.1 N·m
8.0 ± 0.8 in-lb
FRONT BUMPER ASSEMBLY
TSB Revision
EXTERIOR
51-6
DISASSEMBLY SERVICE POINT
.
<<A>> RIVETS REMOVAL
Use a drill [(
φ 4.0 mm(0.16 in)] to make a hole in the rivet to
break it, and remove the rivet.
REASSEMBLY SERVICE POINT
.
>>A<< RIVETS INSTALLATION
Use a rivet tool shown as in the illustration to connect the parts
with rivets by the following procedures:
1. Insert the rivet into a corresponding location.
2. Set the rivet tool at a portion A of rivet.
3. While pushing the flange surface of the rivet onto parts to be
fixed with the rivet tool, press the handle of the tool.
4. Thin part of portion A of the rivet will be cut off and the parts
is fixed in position.
Disassembly steps
1. Hood weatherstrip front
<<
A
>> >>
A
<< 2. Rivet
3. Front bumper reinforcement
4. Front bumper extension A <Some
models>
6. Oil cooler duct <Vehicles with oil
cooler>
6. Front bumper air guide duct
7. Front bumper core
8. Radiator grille
9. Front bumper grille
10. Front fog light bezel <Vehicles with
front fog lights>
11. Front fog light <Vehicles with front fog
light>
12. Front bumper light hole cover
<Vehicles without front fog light>
13. Front bumper harness
14. Front bumper center garnish <Type 1:
Material color>
15. Front bumper center garnish <Type 2:
Chromium plating>
16. Front bumper face
Disassembly steps (Continued)
AC303663AL
Rivet
Drill
Front bumper face
AC205918
AG
1
2
3
4
Portion A
Flange
Rivet
Rivet
Fixing parts
Rivet tool
Rivet tool
Front bumper
face
Front bumper face
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст