Mitsubishi Outlander GS45X. Manual — part 524
EXHAUST PIPE AND MAIN MUFFLER
TSB Revision
INTAKE AND EXHAUST
15-23
Required Special Tool:
• MB991953: Oxygen Sensor Wrench
REMOVAL SERVICE POINTS
.
<<A>> LINER AIR-FUEL RATIO SENSOR/HEATED
OXYGEN SENSOR REMOVAL
Remove the connection and clamp of linear air-fuel ratio sensor
connector or heated oxygen sensor connector, and then use
special tool MB991953 to remove the linear air-fuel ratio sensor
or heated oxygen sensor.
.
Exhaust main muffler and rear
floor panel heat protector
removal steps
1.
Exhaust main muffler
10. Seal ring
11. Exhaust muffler hanger
>>
C
<<
12. Exhaust tail pipe diffuser
16. Rear floor panel heat protector
Center exhaust pipe and front
floor panel rear heat protector
removal steps
2.
Backbone brace
•
Lower side cover (RH) (Refer to
GROUP 52A, Front Floor
Console Assembly
).
•
Turn up the passenger's side floor
carpet.
3.
Linear air-fuel ratio sensor
connection
<<
A
>>
>>
B
4.
Linear air-fuel ratio sensor
5.
Harness cover
•
Front seat assembly (RH) (Refer
to GROUP 52A, Front Seat
Assembly
6.
Heated oxygen sensor connector
connection
<<
A
>>
>>
B
<<
7.
Heated oxygen sensor
8.
Center exhaust pipe
10. Seal ring
13. Exhaust pipe gasket
14. Exhaust muffler hanger
<<
B
>>
>>
A
<<
17. Rivet
18. Front floor rear panel heat
protector
Front exhaust pipe and front
floor panel front heat protector
removal steps
9.
Front exhaust pipe
13. Exhaust pipe gasket
15. Seal ring
19. Dash panel heat protector
<<
B
>>
>>
A
<<
20. Rivet
21. Front floor front panel heat
protector
Center exhaust pipe and front
floor panel rear heat protector
removal steps (Continued)
AC703721
MB991953
AC
Linear air-fuel ratio
sensor or heated
oxygen sensor
EXHAUST PIPE AND MAIN MUFFLER
TSB Revision
INTAKE AND EXHAUST
15-24
<<B>> RIVET REMOVAL
CAUTION
Be careful not to damage the heat protector with the drill.
Use a drill [6.0 mm (0.24 inch)] to make a hole in the rivet to
break it, and then remove the rivet.
INSTALLATION SERVICE POINTS
.
>>A<< RIVET INSTALLATION
Use a rivet tool shown in the illustration to connect the parts
with rivets by the following procedures.
1. Insert the rivet into a corresponding location.
2. Set the rivet tool at a portion A of rivet.
3. While pushing the flange surface of the rivet onto parts to be
fixed with the rivet tool, press the handle of the tool.
4. Thin part of portion A of the rivet will be cut off and the part is
fixed in position.
.
AC301909AB
Heat
protector
Drill
Rivet
AC700168
Heart protector
Rivet tool
AB
1
2
3
4
Rivet
Fixing parts
Rivet tool
Rivet
Portion A
Flange
EXHAUST PIPE AND MAIN MUFFLER
TSB Revision
INTAKE AND EXHAUST
15-25
>>B<< LINER AIR-FUEL RATIO SENSOR/HEATED
OXYGEN SENSOR INSTALLATION
Tighten the linear air-fuel ratio sensor or heated oxygen sensor
to the specified torque by using special tool MB991953.
Tightening torque: 44
± 5 N⋅m (32 ± 3 ft-lb)
.
>>C<< EXHAUST TAIL PIPE DIFFUSER
INSTALLATION
When the part is reused, make sure that there is no excessive
play after installation and that the part is securely fixed.
REMOVAL AND INSTALLATION <3.0L ENGINE>
M1151008702697
AC703721
MB991953
AC
Linear air-fuel ratio
sensor or heated
oxygen sensor
AC802708
50 ± 10 N·m
37 ± 7 ft-lb
50 ± 10 N·m
37 ± 7 ft-lb
41 ± 10 N·m
30 ± 8 ft-lb
41 ± 10 N·m
30 ± 8 ft-lb
7.0 ± 3.0 N·m
62 ± 27 in-lb
5.0 ± 2.0 N·m
45 ± 17 in-lb
5.0 ± 2.0 N·m
45 ± 17 in-lb
8
11
10
9
7
5
13
12
14
15
16
18
1
2
4
6
3
3
N
N
N
N
N
N
N
AB
<FWD>
17
N
9.5 ± 3.5 N·m
84 ± 30 in-lb
EXHAUST PIPE AND MAIN MUFFLER
TSB Revision
INTAKE AND EXHAUST
15-26
REMOVAL SERVICE POINTS
.
<<A>> EXHAUST TAIL PIPE DIFFUSER REMOVAL
Insert the wood and tire lever between exhaust tail pipe diffuser
and exhaust main muffler.
And then turn the tire lever and remove exhaust tail pipe dif-
fuser.
.
AC802709
50 ± 10 N·m
37 ± 7 ft-lb
50 ± 10 N·m
37 ± 7 ft-lb
41 ± 10 N·m
30 ± 8 ft-lb
41 ± 10 N·m
30 ± 8 ft-lb
7.0 ± 3.0 N·m
62 ± 27 in-lb
5.0 ± 2.0 N·m
45 ± 17 in-lb
5.0 ± 2.0 N·m
45 ± 17 in-lb
8
11
10
9
7
5
13
12
14
15
16
18
1
2
4
6
3
3
N
N
N
N
N
N
N
5.0 ± 2.0 N·m
45 ± 17 in-lb
3
AB
<AWD>
17
N
9.5 ± 3.5 N·m
84 ± 30 in-lb
Exhaust main muffler and rear
floor panel heat protector
removal steps
1.
Exhaust main muffler
2.
Gasket
3.
Hanger
<<A>>
17. Exhaust tail pipe diffuser
18. Rear floor panel heat protector
Center exhaust pipe removal
steps
4.
Center exhaust pipe
5.
Seal ring
2.
Gasket
6.
Hanger
Front exhaust pipe and front
floor rear panel heat protector
removal steps
7.
Front exhaust pipe
8.
Gasket
9.
Gasket
5.
Seal ring
10. Front exhaust pipe RH
11. Gasket
12. Dash panel heat protector
<<B>> >>A<<
13. Rivet
14. Front floor front panel heat
protector
<<B>> >>A<<
15. Rivet
16. Front floor rear panel heat protector
AC710455
Exhaust tail pipe diffuser
Wood
AC
Tire lever
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст