Mitsubishi Outlander GS45X. Manual — part 1093
LIFTGATE
TSB Revision
BODY
42A-175
INSTALLATION SERVICE POINT
.
>>A<< STRIKER INSTALLATION
Install the striker so that the striker center does not deviate
more than
±1.5 mm (0.06 inch) from the latch center.
INSPECTION
M1424002100278
LIFTGATE LOCK RELEASE HANDLE (LIFTGATE
OPEN SWITCH) CHECK
<VEHICLES WITH KOS>
LIFTGATE LOCK RELEASE HANDLE (LIFTGATE
LOCK SWITCH) CHECK <VEHICLES WITH KOS>
AC703419AB
+1.5 mm
(0.06 in)
-1.5 mm
(0.06 in)
Striker center
Striker
Latch center
Latch
Switch
position
Terminal
number
Normal value
Push (open)
1
− 2
Continuity
exists (2
Ω or
less)
Release
1
− 2
No continuity
ACA00837AF
Open switch
Switch
position
Terminal
number
Normal value
Push (lock)
2
− 3
Continuity
exists (2
Ω or
less)
Release
2
− 3
No continuity
ACA00837AE
Lock switch
LIFTGATE
TSB Revision
BODY
42A-176
LIFTGATE LOCK ACTUATOR CHECK
LIFTGATE LATCH SWITCH CHECK
Lever
position
Battery
connection
Lever operation
At the
"SET"
position
• Connect
terminal 2 to
negative battery
terminal.
• Connect
terminal 1 to
positive battery
terminal.
Lever moves
from "SET" to
"OPEN" position.
AC302760AG
Set
Lever
Open
Claw position
Terminal
number
Normal value
Unlatch (ON)/
Half-latch (ON)
1
− Ground
Continuity
exists (2
Ω or
less)
Full-latch (OFF) 1
− Ground
No continuity
AC905470AC
Unlatch
(ON)
Half-latch
(ON)
Full-latch
(OFF)
1
LIFTGATE
TSB Revision
BODY
42A-177
REMOVAL AND INSTALLATION <LIFTGATE LOWER>
M1424001700772
INSTALLATION SERVICE POINTS
.
>>A<< LIFTGATE WEATHERSTRIP INSTALLA-
TION
1. The marking on the liftgate weatherstrip should be
positioned at the center of the liftgate lower.
2. Install the weatherstrip according to the order shown in the
figure.
3. Install the weatherstrip according to the direction shown by
the arrow in the figure.
.
Post-installation operation
• Liftgate alignment (Refer to
).
AC713420
1
2
4
3
4
5
AB
20 ± 5 N·m
15 ± 3 ft-lb
2.5 ± 0.5 N·m
23 ± 4 in-lb
7.0 ± 2.0 N·m
43 ± 18 in-lb
7.0 ± 2.0 N·m
43 ± 18 in-lb
2.5 ± 0.5 N·m
23 ± 4 in-lb
:Sectional view of
clip position
Liftgate lock release handle knob
removal
1.
Liftgate lock release handle knob
Striker removal steps
1.
Liftgate lock release handle knob
•
Liftgate lower trim (Refer to
GROUP 52A, Liftgate Trim
>>B<<
2.
Striker
Liftgate latch removal steps
1.
Liftgate lock release handle knob
•
Liftgate lower trim (Refer to
GROUP 52A, Liftgate Trim
3.
Liftgate handle controller
4.
Liftgate latch
Liftgate weatherstrip removal
>>A<<
5.
Liftgate weatherstrip
AC703421AB
1
1
2
2
Positioning mark
LIFTGATE
TSB Revision
BODY
42A-178
>>B<< STRIKER INSTALLATION
Install the striker so that the striker center does not deviate
more than
±1.5 mm (0.06 in) from the latch center.
AC703419AB
+1.5 mm
(0.06 in)
-1.5 mm
(0.06 in)
Striker center
Striker
Latch center
Latch
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст