Mitsubishi Outlander GS45X. Manual — part 1636
DIAGNOSIS
TSB Revision
CVT
23A-101
LOGIC FLOW CHARTS (Monitor Sequence)
.
DTC SET CONDITIONS
Judgment Criteria
• Lockup/select switching solenoid valve activation
command (ON voltage): 1.42 volts or less (0.2
second)
• Lockup/select switching solenoid valve activation
command (OFF voltage): more than 1.42 volts
(0.2 second)
.
OBD-II DRIVE CYCLE PATTERN
Ignition switch : ON (start the engine and keep it for
10 seconds or more)
.
PROBABLE CAUSES
• Malfunction of valve body assembly (Faulty
lockup/select switching solenoid valve)
• Damaged wiring harness and connectors
• Malfunction of TCM
.
PROBABLE CAUSES
• Malfunction of valve body assembly (Faulty
lockup/select switching solenoid valve)
• Damaged wiring harness and connectors
• Malfunction of TCM
AC802632
START
Yes
No
Torque converter clutch or
select switch solenoid activation command
on at circuit voltage 1.42 V
Torque converter clutch or
select switch solenoid activation command
off at circuit voltage > 1.42 V
No
No
Good
Malfunction
END
Yes
Continuous failure for 0.2 sec
Yes
DIAGNOSIS
TSB Revision
CVT
23A-102
DIAGNOSTIC PROCEDURE
STEP 1. M.U.T.-III data list
Item 36: LU/SEL changeover SOL. output
Item 37: LU/SEL changeover SOL. monitor
OK: Check that the output and monitor do not differ
greatly.
Q: Is the check result normal?
YES : Intermittent malfunction
NO : Go to Step 2.
STEP 2. Check the following connector:
• B-125 CVT assembly connector
• C-38 TCM connector
• A-12 Intermediate connector
Check the terminals for a contact status problem and internal
short circuit.
Q: Is the check result normal?
YES : Go to Step 3.
NO : Repair the defective connector.
STEP 3. Check for open circuit and short to ground in the
wiring harness between the TCM connector and the CVT
assembly connector.
Between C-38 TCM connector (terminal No.14) and B-125 CVT
assembly connector (terminal No.4)
Q: Is the check result normal?
YES : Go to Step 4.
NO : Repair the wiring harness.
STEP 4. Lockup/select switching solenoid valve single unit
check
Refer to
.
Q: Is the check result normal?
YES : Go to Step 5.
NO : Replace the valve body assembly.
STEP 5. Symptom recheck after erasing diagnostic trouble
code
Q: Is the check result normal?
YES : Intermittent malfunction
NO : Replace TCM.
DIAGNOSIS
TSB Revision
CVT
23A-103
DTC P1745: Monitoring of Percentage Change in Pulley Ratio
.
DIAGNOSTIC FUNCTION
TCM conducts fault detection by monitoring the inter-
nal calculated value.
.
JUDGEMENT CRITERIA
Percentage change in pulley ratio is larger than the
standard value.
.
PROBABLE CAUSES
• Malfunction of TCM
DIAGNOSTIC PROCEDURE
STEP 1. Symptom recheck after erasing diagnosis code
Q: Is the check result normal?
YES : Intermittent malfunction
NO : Replace TCM.
DTC P1773: Malfunction of ABS
.
DIAGNOSTIC FUNCTION
TCM detects the ABS abnormality.
.
DESCRIPTIONS OF MONITOR METHODS
• When the ABS error signal reception continues
for 0.5 seconds.
.
MONITOR EXECUTION
• When 1.05 seconds have elapsed after TCM
started (not during M.U.T.-III communication)
.
MONITOR EXECUTION CONDITIONS
(OTHER MONITOR AND SENSOR)
Other Monitor (There is no temporary DTC stored
in memory for the item monitored below)
• Not applicable
Sensor (The sensor below is determined to be
normal)
• Not applicable
.
DIAGNOSIS
TSB Revision
CVT
23A-104
LOGIC FLOW CHARTS (Monitor Sequence)
.
DTC SET CONDITIONS
Check Conditions
• Time after TCM start: more than 1.05 seconds.
Judgment Criteria
• ABS status: malfunction
.
OBD-II DRIVE CYCLE PATTERN
Ignition switch : ON (start the engine and keep it for
10 seconds or more, not during M.U.T.-III communi-
cation)
.
PROBABLE CAUSES
• Malfunction of the ABS system
• Malfunction of TCM
DIAGNOSTIC PROCEDURE
STEP 1. ABS system DTC check
Q: Is the ABS system DTC set?
YES : Carry out the troubleshooting for ABS.
NO : Go to Step 2.
AC802633
START
Yes
No
Yes
No
Yes
No
Good
Malfunction
END
Continuous failure for 0.5 sec
ABS status is "Malfunction"
All secondary parameters
are in the enable condition.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст