Mitsubishi Outlander GS45X. Manual — part 1634
DIAGNOSIS
TSB Revision
CVT
23A-93
STEP 2. Check for open circuit in power supply wiring
harness
• Between relay box and C-37 TCM backup power supply
connector (terminal No.31)
• Between relay box and A-18X CVT control relay (terminal
No.4)
Q: Is the check result normal?
YES : Go to Step 3.
NO : Repair the wiring harness.
STEP 3. Symptom recheck after erasing diagnostic trouble
code
Q: Is the check result normal?
YES : Intermittent malfunction
NO : Replace TCM.
DTC P1706: Malfunction of Throttle Signal
.
DIAGNOSTIC FUNCTION
TCM detects the abnormality in the throttle position
signal sent from the ECM.
.
DESCRIPTIONS OF MONITOR METHODS
• The difference between the throttle position sig-
nal received from the ECM and the correspond-
ing turnover value is 1.37 V or more, and this
status continues for 1 second.
.
MONITOR EXECUTION
• Transmission range: D
.
MONITOR EXECUTION CONDITIONS
(OTHER MONITOR AND SENSOR)
Other Monitor (There is no temporary DTC stored
in memory for the item monitored below)
• P0705: Malfunction of transmission range switch
• P0715: Malfunction of primary pulley speed sen-
sor
• P0720: Malfunction of secondary pulley speed
sensor
• P0725: Malfunction of engine speed
• P0741: Abnormality in lockup function
• P0746: Abnormality in hydraulic control system
function
• P0841: Abnormality in line pressure sensor func-
tion
Sensor (The sensor below is determined to be
normal)
• Transmission range switch
• Primary pulley speed sensor
• Secondary pulley speed sensor
.
DIAGNOSIS
TSB Revision
CVT
23A-94
LOGIC FLOW CHARTS (Monitor Sequence)
.
DTC SET CONDITIONS
Check Conditions
• Transmission range switch position: D.
• Voltage of battery: 9 volts or more.
• Voltage of battery: 16 volts or less.
JUDGMENT CRITERIA
• Throttle position toggle signal on CAN: not
change. (1 second)
.
OBD-II DRIVE CYCLE PATTERN
Ignition switch : ON (start the engine and keep it for
10 seconds or more)
.
PROBABLE CAUSES
• Malfunction of the CAN bus
• Malfunction of engine system
• Malfunction of TCM
AC710016
START
Yes
No
Throttle position toggle signal on CAN is not change
Yes
No
Yes
Good
Malfunction
END
No
Continuous failure for 1 sec
Secondary parameters are
in the enable condition.
DIAGNOSIS
TSB Revision
CVT
23A-95
DIAGNOSTIC PROCEDURE
STEP 1. Using scan tool MB991958, diagnose the CAN bus
line.
Use scan tool MB991958 to perform the CAN bus diagnosis.
Q: Is the check result normal?
YES : Go to Step 2.
NO : Repair the CAN bus lines (Refer to GROUP 54C
−
Troubleshooting, Diagnostic Trouble Code Chart
).
STEP 2. Scan tool MB991958 diagnostic trouble code
Check if the engine-related diagnostic trouble code is set.
Q: Is diagnostic trouble code set?
YES : Diagnose the engine control system.
NO : Go to Step 3.
STEP 3. Symptom recheck after erasing diagnostic trouble
code
Q: Is the check result normal?
YES : Intermittent malfunction
NO : Replace TCM.
DTC P1710: Malfunction of Vehicle Speed Signal
.
DIAGNOSTIC FUNCTION
TCM conducts fault detection by detecting the rapid
change in the estimated vehicle speed signal
received from the ABC-ECU.
.
JUDGMENT CRITERIA
• Difference between the estimated vehicle speed
and the one measured before 0.1 second is 29
km/h (18.0 mph) or more.
• The status with the vehicle speed of 10 km/h (6.2
mph) or more and with the estimated vehicle
speed of 2 km/h (1.2 mph) or less continues for
20 seconds.
.
PROBABLE CAUSES
• Malfunction of the CAN bus
• Malfunction of TCM
DIAGNOSTIC PROCEDURE
STEP 1. Troubleshoot the CAN system if diagnosis code
U0121 is set.
Q: Is the diagnosis code U0121 set?
YES : Diagnose the CAN system.
NO : Go to Step 2.
DIAGNOSIS
TSB Revision
CVT
23A-96
STEP 2. M.U.T.-III data list
• Item 21: Vehicle speed (inference)
• Item 22: Real vehicle speed
OK: Vehicle speed signal and vehicle speed do not dif-
fer greatly.
Q: Is the check result normal?
YES : Intermittent malfunction
NO : Go to Step 3.
STEP 3. Check ABS-related diagnosis codes.
Q: Is the ABS-related diagnosis code set?
YES : Carry out the appropriate troubleshooting.
NO : Go to Step 4.
STEP 4. Symptom recheck after erasing diagnosis code
Q: Is the check result normal?
YES : Intermittent malfunction
NO : Replace TCM.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст