Mitsubishi Outlander GS45X. Manual — part 1362
WINDSHIELD WIPER AND WASHER
TSB Revision
EXTERIOR
51-71
STEP 3. Windshield wiper operation check
Check that the windshield wipers work normally.
Q: Is the check result normal?
YES : Go to Step 4.
NO : Refer to trouble symptom chart
STEP 4. Windshield washer operation check
Check that the windshield washer works normally.
Q: Is the check result normal?
YES : Go to Step 5.
NO : Refer to Inspection Procedure 10 "The windshield
washer does not work normally
STEP 5. System retest
Check that the intelligent washer function works normally.
Q: Is the check result normal?
YES : Intermittent malfunction (Refer to GROUP 00
− How
to Use Troubleshooting/Inspection Service Points
−
How to Cope with Intermittent Malfunction
NO : Replace the ETACS-ECU.
Inspection Procedure 12: Delayed finishing wipe function does not work normally.
CAUTION
Before replacing the ECU, ensure that the power
supply circuit, the ground circuit and the com-
munication circuit are normal.
.
COMMENT ON TROUBLE SYMPTOM
If the delayed finishing wipe function does not prop-
erly operate, the input circuit of windshield wiper
switch, the input circuit of windshield washer switch,
or ETACS-ECU may be defective.
.
PROBABLE CAUSES
• Malfunction of column switch
• Malfunction of ETACS-ECU
• Damaged harness wires and connectors
DIAGNOSIS
Required Special Tools:
• MB991223: Harness Set
• MB992006: Extra Fine Probe
• MB991958: Scan Tool (M.U.T.-III Sub Assembly)
• MB991824: V.C.I.
• MB991827: M.U.T.-III USB Cable
• MB991910: M.U.T.-III Main Harness A
WINDSHIELD WIPER AND WASHER
TSB Revision
EXTERIOR
51-72
STEP 1. Use the scan tool MB991958 to check if an
ETACS-related diagnostic trouble code is set.
Connect the scan tool. Refer to GROUP 54A ETACS, "Diag-
nostic function
."
Q: Is the diagnostic trouble code set?
YES : Diagnose the ETACS-ECU. Refer to GROUP 54A
ETACS, "Diagnostic trouble code chart
."
NO : Go to Step 2.
STEP 2. Check the ETACS-ECU customization function.
Use the ETACS-ECU customization function to check that the
"front wiper washer" is set to "On with delayed finishing wipe
function."
Q: Is the check result normal?
YES : Go to Step 3.
NO : Use the ETACS-ECU customization function to set
the "front wiper washer" to "On with delayed finishing
wipe function." (Refer to
.)
STEP 3. Windshield wiper operation check
Check that the windshield wipers work normally.
Q: Is the check result normal?
YES : Go to Step 4.
NO : Refer to trouble symptom chart
STEP 4. Windshield washer operation check
Check that the windshield washers work normally.
Q: Is the check result normal?
YES : Go to Step 5.
NO : Refer to Inspection Procedure 10 "Windshield
washers do not work normally
ZC501967
AC404789
AC701411AB
MB991824
MB991827
MB991910
Data link
connector
WINDSHIELD WIPER AND WASHER
TSB Revision
EXTERIOR
51-73
STEP 5. Retest the system
Check that the delayed finishing wipe function works normally.
Q: Is the check result normal?
YES : Intermittent malfunction. (Refer to GROUP 00
− How
to Use Troubleshooting/Inspection Service Points
−
How to Cope with Intermittent Malfunction
NO : Replace the ETACS-ECU.
DATA LIST REFERENCE TABLE
M1511015100048
LIN (LIGHTING CONTROL SENSOR)
Item No. Scan tool display
Check condition
Normal condition
7005
RLS Rain sensor ON/OFF
When the wiper switch is AUTO position
ON
When a switch (except the wiper switch) is
AUTO position
OFF
7006
RLS Rain sensor sensitivity Changes from 1 to 5 according to the
wiper volume.
1, 2, 3, 4, 5
7008
RLS Wiper auto stop SW
When the windshield wiper is in operation Park
Other than above
Outside park
7013
RLS Wiper control output
When the operation is not requested from
lighting control sensor (rain sensor).
OFF
When the LO operation is requested from
lighting control sensor (rain sensor)
LO
When the HI operation is requested from
lighting control sensor (rain sensor)
HI
7020
RLS RS measurement
value(RS1)
When the lighting control sensor (rain
sensor) detects raindrops
The sensor 1 detects
raindrops and the
value changes.
7021
RLS RS measurement
value(RS2)
When the lighting control sensor (rain
sensor) detects raindrops
The sensor 2 detects
raindrops and the
value changes.
7022
RLS RS adaptation
value(RS1)
When initializing after the adaptation
(sensor 1)
The amount of output
when initializing
(sensor 1)
7023
RLS RS adaptation
value(RS2)
When initializing after the adaptation
(sensor 2)
The amount of output
when initializing
(sensor 2)
7024
RLS RS adaptation gain
level
When initializing after the adaptation
The calibrated value of
initializing
WINDSHIELD WIPER AND WASHER
TSB Revision
EXTERIOR
51-74
ON-VEHICLE SERVICE
WINDSHIELD INTERMITTENT WIPER INSPECTION
M1511023600145
1. Check that the intermittent wiper interval is
changed as the windshield intermittent wiper vol-
ume is operated.
2. Turn the windshield intermittent wiper switch to
the intermittent operation position. Use the scan
tool to set a simulated vehicle speed with the
wiper volume held. The intermittent wiper interval
should be changed as the simulated vehicle
speed is changed.
3. If either of above is defective, carry out the trou-
)
LIGHTING CONTROL SENSOR (RAIN SENSOR) INSPECTION
M1511028400049
Under clear weather (windshield glass is dry), turn
the ignition switch to "ON" position and wiper switch
to "AUTO" position. Check that the wiper works when
applying water to the upper part of the windshield
glass where the lighting control sensor is installed. If
there is a malfunction, perform the troubleshooting
(Refer to
).
INTELLIGENT WASHING FUNCTION INSPECTION
M1511029600080
1. Operate the windshield washer switch for less
than 0.35 second with the ignition switch in the
ACC or ON position to check whether the
intelligent washer function works normally.
2. If not, carry out the troubleshooting. (Refer to
NOTE: Check that the intelligent washer function is
set to "Enabled" with the customization function.
(Refer to
.)
DELAYED FINISHING WIPE FUNCTION INSPECTION
M1511029800040
1. When the washer lever of the column switch is
operated for 0.5 second or longer with the ignition
switch in the ACC or ON position, or when the
intelligent washer function is enabled, the delayed
finishing wipe function injects the washer fluid and
operates the wiper. The wiper operates once for 6
seconds after the wiper operation is stopped.
Check that the delayed finishing wipe function
works normally.
2. If not, carry out the troubleshooting. (Refer to
NOTE: Check that the delayed finishing wipe func-
tion is set by the customization function. (Refer to
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст