Mitsubishi Outlander GS45X. Manual — part 1363
WINDSHIELD WIPER AND WASHER
TSB Revision
EXTERIOR
51-75
CONFIGURATION FUNCTION
M1511027402031
Using the ETACS system of scan tool MB991958,
the following functions can be programmed. The pro-
grammed information is held even when the battery
is disconnected.
Adjustment
item (scan tool
MB991958
display)
Adjustment item
Adjusting contents
(scan tool MB991958
display)
Adjusting contents
Front wiper
operation
Adjustment of the
intermittent
windshield wiper
operation <vehicles
without auto light>
Normal INT
Intermittent wiper interval is fixed to 4
seconds.
Variable INT
Intermittent wiper interval is calculated only
by the wiper volume control.
Speed Sensitive
Intermittent wiper interval is calculated
according to the intermittent wiper volume
control and vehicle speed (initial
condition).
Adjustment of the
intermittent
windshield wiper
operation <vehicles
with auto light>
Normal INT
Intermittent wiper interval is fixed to 4
seconds.
Variable INT
Intermittent wiper interval is calculated only
by the wiper volume control.
Speed Sensitive
Intermittent wiper interval is calculated
according to the intermittent wiper volume
control and vehicle speed.
Rain Sensitive
Intermittent wiper interval is calculated
according to the intermittent wiper volume
control and lighting control sensor (initial
condition).
Front wiper
washer
Disabling or
enabling
washer-linked wiper
function
Only Washer
No function
Washer & Wiper
With function: Without delayed finishing
wipe function (Initial condition)
With after wipe
With function: With delayed finishing wipe
function
Intelligent
washer
With/without
intelligent washer
function
Disable
No function
Enable
With function (initial condition)
WINDSHIELD WIPER AND WASHER
TSB Revision
EXTERIOR
51-76
WINDSHIELD WIPER
REMOVAL AND INSTALLATION
M1511007901398
Required Special Tool:
• MB991955: M.U.T.-III sub-assembly
• MB991223: Harness set
AC808972
Section B – B
Section C – C
A
B
C
5
2
5
(LH)
5
(LH)
5
(RH)
5
(RH)
8
NOTE
: Clip positions
: Claw positions
1
3
4
4
B
8
7
7
5
6
6
D
N
View D
Specified grease: Multipurpose
grease SAE J310, NLGI No.1
(mineral oil + Li) or equivalent
View A
Clip
Claw
8.0 ± 2.0 N·m
71 ± 18 in-lb
8.0 ± 2.0 N·m
71 ± 18 in-lb
8.0 ± 2.0 N·m
71 ± 18 in-lb
27 ± 3 N·m
20 ± 2 ft-lb
C
AC
Wiper blade removal steps
1.
Wiper blade assembly
>>C<<
2.
Wiper blade
Windshield wiper motor and link
assembly removal steps
>>B<<
3.
Wiper arm and blade assembly
4.
Hood weatherstrip rear
5.
Front deck garnish
6.
Windshield wiper link
7.
Wiper motor link plate
<<A>>
>>A<<
8.
Windshield wiper motor
Windshield wiper motor and link
assembly removal steps
WINDSHIELD WIPER AND WASHER
TSB Revision
EXTERIOR
51-77
NOTE: For removal and installation of the wiper and
washer switch, refer to GROUP 54A, Column switch
REMOVAL SERVICE POINT
.
<<A>> WINDSHIELD WIPER MOTOR REMOVAL
1. Remove the wiper link rod joint from the wiper motor link
plate.
2. Connect the wiper motor to a battery, and rotate the link
plate as shown.
3. In this position, withdraw the link plate from the wiper link
assembly.
AC511723AC
Wiper motor
link plate
AC511724
4
5
3
1
2
4
5
3
1
2
AB
Wiper motor
<Link plate disconnected>
<Link plate rotated>
WINDSHIELD WIPER AND WASHER
TSB Revision
EXTERIOR
51-78
INSTALLATION SERVICE POINT
.
>>A<< WINDSHIELD WIPER MOTOR INSTALLA-
TION
1. Position the wiper motor link plate as shown, and assemble
it to the wiper link assembly.
NOTE:
.
•
The link plate can be assembled to the wiper link assem-
bly only at this position. If not, rotate the link plate to this
position (Refer to Stop Position Check,
).
•
Wiper motor replacement parts are supplied with the link
plate positioned as shown.
2. Connect the assembled wiper motor to a battery, and set it
to the automatic stop position (Refer to Stop Position Check,
).
3. Apply grease to the inside of link rod joint (as required) and
connect the link rod to wiper motor link plate.
.
>>B<< WIPER ARM AND BLADE ASSEMBLY
INSTALLATION
Install the wiper arm and blade assembly at the specified posi-
tions.
(A):
φ 2 marking ± 5 mm(0.20 in)
.
AC511725AB
Wiper motor link plate
AC702508
AD
A
A
A
A
Ø2 marking
Ø2 marking
5(0.20)
5(0.20)
Ø2marking
Section A – A
Unit: mm (in)
Front deck garnish
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст