Mitsubishi Outlander GS45X. Manual — part 1371
MARK
TSB Revision
EXTERIOR
51-107
INSTALLATION SERVICE POINT
.
>>A<< MARK APPLICATION
1. Installation position
Attach each mark to the position shown in the illustration.
AC809542
A
A
AC
13 mm
(0.5 in)
13 mm (0.5 in)
Section A – A
Center line of vehicle
Liftgate garnish
lower end
2. Rear three-diamond mark <Vehicles without liftgate molding>
Liftgate garnish upper end
AC809543
A
A
AC
5 mm
(0.2 in)
5 mm (0.2 in)
Section A – A
Center line of vehicle
Liftgate garnish
lower end
2. Rear three-diamond mark <Vehicles with liftgate molding>
Liftgate garnish upper end
Liftgate molding
ACA02806AB
31.8 mm
(1.25 in)
66.5 mm
(2.62 in)
Liftgate panel
end
3. MITSUBISHI mark (Vehicles for USA and Canada)
MARK
TSB Revision
EXTERIOR
51-108
AC709768 AE
58.4 mm
(2.30 in)
24.4 mm
(0.96 in)
59.9 mm
(2.36 in)
Liftgate panel end
4. OUTLANDER mark <Vehicles for Puerto Rico and Mexico>
ACA02818AB
67.1 mm
(2.64 in)
37.6 mm
(1.48 in)
20.4 mm
(0.8 in)
Liftgate panel
end
5. OUTLANDER mark (Vehicles for USA and Canada)
6. V6 mark
(Vehicles for USA and Canada)
54.3 mm
(2.14 in)
ACA02819AB
58.7 mm
(2.31 in)
75.6 mm
(2.98 in)
Liftgate panel
end
7.V6 mark <Vehicles for Puerto Rico and Mexico>
MARK
TSB Revision
EXTERIOR
51-109
2. Installation procedure
(1) Use 3M
™ AAD Part number 8906 or equivalent to clean
the mark installation surfaces on the body.
AC704106 AG
8. V6 mark
Front
Front
<RH>
<LH>
Fender panel end
Side turn-signal light
Side turn-signal light
49.1 mm
(1.93 in)
67.3 mm
(2.65 in)
50.9 mm
(2.00 in)
67.3 mm
(2.65 in)
49.9 mm
(1.93 in)
50.5 mm
(1.99 in)
ACA01442AC
9. 4WD mark <4WD>
82.8 mm
Defogger
Ceramic line end
Tailgate window glass hem line
Application tape
10.7 mm
(0.42 in)
82.2 mm
(3.24 in)
82.8 mm
(3.26 in)
15.8 mm
(0.62 in)
AC802546 AD
10. ULEV (ULTRA LOW EMISSIONS VEHICLE) mark (LH) <Vehicles for California (3000)>
Ceramic line
7.0 ± 5.0 mm
(0.28 ± 0.20 in)
Quarter window
glass end line
(0.20 ± 0.04 in)
5.0 ± 1.0 mm
OUTSIDE MIRROR
TSB Revision
EXTERIOR
51-110
CAUTION
When attaching the marks, the ambient temperature
should be 20
− 38°C (60 − 100°F) and air should be com-
pletely free of dust. If the ambient temperature is lower
than 20
°C (60°F), the marks and places on the body where
the marks are to be attached should be heated to 20
− 30°C
(60
− 86°F).
(2) Peel off the protection sheet on the back of the marks to
paste it on the installation position.
OUTSIDE MIRROR
GENERAL INFORMATION
M1511000101368
DOOR MIRROR OPERATION
Remote Controlled Mirror Operation
• The mirror on the door mirror moves up/down
and left/right by operating the remote controlled
door mirror switch when the ignition switch is at
the "ON" or "ACC" position.
Heated Door Mirror Operation
• The rear window defogger relay switch is acti-
vated (ON) by turning on the A/C-ECU built-in
rear window defogger switch when the ignition
switch is in the "ON" position. When the rear win-
dow defogger relay is turned ON, power is sup-
plied to the rear window defogger and door
mirror, and the heater of the door mirror (heated
door mirror) starts operations. The rear window
defogger comes with a timer function and will
automatically turn OFF the switch approximately
20 minutes after the rear window defogger switch
is turned ON. The heated door mirror operations
are also terminated along with the rear window
defogger, at this time.
HEATED DOOR MIRROR DIAGNOSIS
TROUBLESHOOTING STRATEGY
M1511014600523
Diagnosis should be carried out by the following pro-
cedures.
1. Gather the information from the customer.
2. Verify that the condition described by the
customer exists.
3. Find the malfunction by the following Symptom
Chart.
4. Verify the malfunction is eliminated.
TROUBLE SYMPTOM CHART
M1511015001271
Trouble symptom
Inspection
procedure
No.
Reference
page
None of the heated door mirrors operate
1
Left or right side heated door mirror does not operate
2
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст