Mitsubishi Outlander GS45X. Manual — part 1188
TPMS TRANSMITTER
TSB Revision
WIRELESS CONTROL MODULE (WCM)
42C-119
<<C>> SEAL WASHER/VALVE REMOVAL
CAUTION
Remove the seal washer to prevent scratching the valve of
the TPMS transmitter.
1. Hold the TPMS transmitter and the seal washer, then extract
the seal washer. Take care to not damage the valve thread.
2. Clean the TPMS transmitter and the valve stem. <In case of
not removing the valve>
NOTE: If the valve comes out from the transmitter, install it
to where it was. (This is not failure)
3. Removal the valve from housing as shown.
AC609528
AC808700 AB
Seal washer
AC808701AB
AC609528
AC904883
Valve
Housing
AB
TPMS TRANSMITTER
TSB Revision
WIRELESS CONTROL MODULE (WCM)
42C-120
INSTALLATION SERVICE POINTS
.
>>A<< VALVE/SEAL WASHER/TPMS TRANSMIT-
TER/NUT INSTALLATION
CAUTION
Install the seal washer to prevent scratching the valve of
the TPMS transmitter.
1. Install the valve to housing as shown.
2. Insert the seal washer up to the base of the TPMS
transmitter, making sure to secure the valve base with a
thumb as shown.
Wipe the seal and threading.
CAUTION
• Visually check that TPMS transmitter is not deformed
or damaged.
• When installing the TPMS transmitter, be sure the rim,
seal valve and nut are clean.
• Ensure the grommet is located inside the valve hole
before installing the nut.
• While installing the nut, push the TPMS transmitter to
maintain the lower lip of the transmitter case is in con-
tact with the rim without clearance.
• While installing the valve nut, ensure the tool is kept
aligned to the valve and the valve hole.
3. Install the valve, in the valve hole, without modifying the
angle of the stem (retain position of delivery). The laser
marking should be visible at the operator.
AC609528
AC904883
Valve
Housing
AC
AC808702
AB
Seal washer
Seal washer
TPMS transmitter
Part of rubber
AC808703AB
TPMS TRANSMITTER
TSB Revision
WIRELESS CONTROL MODULE (WCM)
42C-121
4. When the valve is completely inserted, maintain the TPMS
transmitter in contact with the rim, then screw manually the
nut until the contact with the wheel.
5. While maintaining the TPMS transmitter contact with the rim
by applying pressure to the back of the valve, slightly press
on the cap to wards the center of the wheel in order to adapt
the angle of the valve/TPMS transmitter to the profile of the
rim.
It is mandatory to guarantee the contact of the housing unit
on the rim drop center.
6. While maintaining the TPMS transmitter and valve in
position, screw the nut with a torque wrench.
Take care that the wrench socket is correctly inserted on the
nut.
Specified torque: 8.0
± 0.5 N⋅m (71 ± 4 in-lb)
.
>>B<< TIRE BEAD MOUNTING
1. Prepare the tire and fix the rim as usual.
AC808704 AB
AC808705 AB
AC808709 AB
AC609532
TPMS TRANSMITTER
TSB Revision
WIRELESS CONTROL MODULE (WCM)
42C-122
2. Put the tire on the rim, so that the cross point of the belt with
the rim is approximately 20 cm (7.9 inch) away from the
valve.
3. Engage the shoe and make sure that 20 cm (7.9 inch) is
maintained between the cross point and the valve.
The arrow shows the direction of rotation of the wheel.
4. Turn the wheel in order to engage all the first side of the tire.
NOTE: The standard shoes can pass over the sensor with-
out damaging it.
5. Put the second side of the tire in position, so that the cross
point of the belt with the rim is approximately 20 cm (7.9
inch) away from the valve. The curved arrow shows the
direction of rotation of the wheel.
6. Turn the wheel in order to engage all of the second side of
the tire.
NOTE: The standard shoes can pass over the sensor with-
out damaging it.
.
AC609533AB
AC609534
AC609535
AC609536 AB
AC609537
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст