Mitsubishi Outlander GS45X. Manual — part 1583
THERMOSTAT
TSB Revision
ENGINE COOLING
14-35
REMOVAL SERVICE POINT
.
<<A>> HOSE CLIP/RADIATOR LOWER HOSE DIS-
CONNECTION
1. Make mating marks on the radiator hose and the hose
clamp as shown to install them in the original position. Then,
remove them.
2. Break off the tip of hose clip claw and spread out the hose
clip.
NOTE: If there is a hose clip claw, the hose clip cannot
spread to capacity because the claw contacts the hose clip.
3. Disconnect the radiator lower hose.
INSTALLATION SERVICE POINTS
.
>>A<< THERMOSTAT INSTALLATION
CAUTION
Avoid adhesion of grease to the rubber ring of the thermo-
stat. If the rubber ring is damaged, replace the thermostat.
Install the thermostat with care to avoid peeling or damage to
the rubber ring. When installing the thermostat, face the jiggle
valve of the thermostat upward.
.
>>B<< HOSE CLIP/RADIATOR LOWER HOSE
CONNECTION
CAUTION
Never reuse the hose clip whose claw is broken off to pre-
vent the rusting.
1. Make mating mark on a new hose clip in the same position
as the remove one.
AC606081
Mating marks
AH
AC302615
Hose clip
Claw (Tip)
AE
AC005977AB
Rubber ring
Jiggle valve
THERMOSTAT
TSB Revision
ENGINE COOLING
14-36
2. Insert the radiator hose until the protrusion of the water inlet
fitting.
3. Align the mating marks on the radiator hose and hose
clamp, and then connect the radiator hose.
4. Remove the hose clip claw to tighten the radiator hose.
REMOVAL AND INSTALLATION <3.0L ENGINE>
M1141002403162
AC606082
Protrusion
Pipe, fitting, or etc.
BD
Mating marks
Pre-removal and Post-installation Operation
• Engine Coolant Draining and Refilling (Refer to
• Air Cleaner Removal and Installation (Refer to GROUP
15, Air Cleaner
• Battery and Battery Tray Removal and Installation (Refer
to GROUP 54A, Battery
AC703114
2
3
4
23 ± 6 N·m
17 ± 4 ft-lb
AD
1
N
Removal steps
<<
A
>>
>>
B
<<
1.
Hose clip
<<A>>
>>B<<
2.
Radiator lower hose connection
3.
Water inlet fitting
>>A<<
4.
Thermostat
Removal steps (Continued)
THERMOSTAT
TSB Revision
ENGINE COOLING
14-37
REMOVAL SERVICE POINT
.
<<A>> HOSE CLIP/RADIATOR LOWER HOSE DIS-
CONNECTION
1. Make mating marks on the radiator hose and the hose
clamp as shown to install them in the original position. Then,
remove them.
2. Break off the tip of hose clip claw and spread out the hose
clip.
NOTE: If there is a hose clip claw, the hose clip cannot
spread to capacity because the claw contacts the hose clip.
3. Disconnect the radiator hose.
INSTALLATION SERVICE POINTS
.
>>A<< THERMOSTAT INSTALLATION
CAUTION
Make absolutely sure that no oil adheres to the rubber ring
of the thermostat. Also do not fold or scratch the rubber
ring during installation.
Install the thermostat so that the jiggle valve is facing straight
up. Be careful not to fold or scratch the rubber ring.
.
AC606081
Mating marks
AH
AC302615
Hose clip
Claw (Tip)
AE
AC703116
Jiggle valve
Rubber ring
AB
THERMOSTAT
TSB Revision
ENGINE COOLING
14-38
>>B<< HOSE CLIP/RADIATOR LOWER HOSE
INSTALLATION
CAUTION
Never reuse the hose clip whose claw is broken off to pre-
vent the rusting.
1. Make mating mark on a new hose clip in the same position
as the remove one.
2. Insert the radiator hose until the protrusion of the water inlet
fitting.
3. Align the mating marks on the radiator hose and hose
clamp, and then connect the radiator hose.
4. Remove the hose clip claw to tighten the radiator hose.
INSPECTION
M1141002501884
.
Thermostat Check
1. Immerse the thermostat in water, and heat the water while
stirring. Check the thermostat valve opening temperature.
Standard value:
Valve opening temperature:
87
± 1.5°C (189 ± 3°F) <2.4L ENGINE>
82
± 1.5°C (180 ± 3°F) <3.0L ENGINE>
2. Check that the amount of valve lift is at the standard value
when the water is at the full-opening temperature.
NOTE: Measure the valve height when the thermostat is
fully closed, and use this measurement to compare the
valve height when the thermostat is fully open.
Standard value:
Full-opening temperature: 95
°C (203°F)
Amount of valve lift:
8.5 mm (0.335 inch) or more <2.4L ENGINE>
9.0 mm (0.354 inch) or more <3.0L ENGINE>
AC606082
Protrusion
Pipe, fitting, or etc.
BD
Mating marks
AC703118AB
AC703119
Valve lift
AB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст