Mitsubishi Outlander GS45X. Manual — part 1584
WATER PUMP
TSB Revision
ENGINE COOLING
14-39
WATER PUMP
REMOVAL AND INSTALLATION <2.4L ENGINE>
M1141002702182
Pre-removal Operation
• Engine Coolant Draining (Refer to
• Drive Belt Removal (Refer to GROUP 11A, Crankshaft
Pulley
).
Post-installation Operation
• Drive Belt Installation (Refer to GROUP 11A, Crankshaft
Pulley
).
• Drive Belt Tension Check (Refer to GROUP 11A, On-vehi-
cle Service
− Drive Belt Tension Check and Adjustment
).
• Engine Coolant Refilling (Refer to
AC509330
2
1
4
5
N
N
AB
3
24 ± 3 N·m
18 ± 2 ft-lb
24 ± 3 N·m
18 ± 2 ft-lb
24 ± 3 N·m
18 ± 2 ft-lb
9.0 ± 1.0 N·m
80 ± 9 in-lb
Removal steps
1.
Water pump pulley
2.
Water pump inlet pipe mounting
nuts
3.
Water pump
4.
Cooling water line gasket
5.
Water pump gasket
Removal steps (Continued)
WATER PUMP
TSB Revision
ENGINE COOLING
14-40
REMOVAL AND INSTALLATION <3.0L ENGINE>
M1141002701888
Pre-removal and Post-installation Operation
• Engine Coolant Draining and Refilling (Refer to
• Timing Belt Removal and Installation (Refer to GROUP
11C, Timing Belt
).
AC703120
1
2
23 ± 6 N·m
17 ± 4 ft-lb
N
AB
Removal steps
1.
Water pump
2.
Water pump gasket
WATER HOSE AND WATER PIPE
TSB Revision
ENGINE COOLING
14-41
WATER HOSE AND WATER PIPE
REMOVAL AND INSTALLATION <2.4L ENGINE>
M1141003304042
Pre-removal Operation
• Engine Coolant Draining (Refer to
• Engine Upper Cover Removal (Refer to GROUP 11A,
Camshaft
• Air Cleaner Assembly Removal (Refer to GROUP 15, Air
Cleaner
).
• Thermostat Removal (Refer to
Post-installation Operation
• Thermostat Installation (Refer to
• Air Cleaner Assembly Installation (Refer to GROUP 15,
Air Cleaner
).
• Engine Upper Cover Installation (Refer to GROUP 11A,
Camshaft
).
• Engine Coolant Refilling (Refer to
AC710021
1
3
4
5
6
7
8
9
10
11
12
12
13
14
15
16
17
N
N
N
N
AD
18
19
20
21
N
N
11 ± 1 N·m
98 ± 8 in-lb
24 ± 3 N·m
18 ± 2 ft-lb
11 ± 1 N·m
98 ± 8 in-lb
24 ± 3 N·m
18 ± 2 ft-lb
24 ± 3 N·m
18 ± 2 ft-lb
24 ± 3 N·m
18 ± 2 ft-lb
24 ± 3 N·m
18 ± 2 ft-lb
5.0 ± 1.0 N·m
44 ± 9 in-lb
20 ± 2 N·m
15 ± 1 ft-lb
2
N
30 ± 9 N·m
22 ± 7 ft-lb
Removal steps
1.
Vacuum pipe assembly
<<
A
>>
>>
C
<<
2.
Hose clip
<<
A
>>
>>
C
<<
3.
Radiator upper hose connection
4.
Throttle body water feed hose
5.
Water outlet fitting
6.
Water outlet fitting gasket
7.
Engine coolant temperature
sensor connector connection
<<
B
>>
>>
B
<<
8.
Engine coolant temperature
sensor
9.
Ground cable connection
10. Control wiring harness
connection
11. EGR valve pipe
12. EGR pipe gasket
13. Water hose
Removal steps (Continued)
WATER HOSE AND WATER PIPE
TSB Revision
ENGINE COOLING
14-42
Required Special Tool:
• MB992042: Water Temperature Sensor Wrench
REMOVAL SERVICE POINTS
.
<<A>> HOSE CLIP/RADIATOR UPPER HOSE DIS-
CONNECTION
1. Make mating marks on the radiator hose and the hose
clamp as shown to install them in the original position. Then,
remove them.
2. Break off the tip of hose clip claw and spread out the hose
clip.
NOTE: If there is a hose clip claw, the hose clip cannot
spread to capacity because the claw contacts the hose clip.
3. Disconnect the radiator lower hose.
.
<<B>> ENGINE COOLANT TEMPERATURE
SENSOR REMOVAL
Use special tool MB992042 to remove the engine coolant tem-
perature sensor.
14. Wiring harness bracket
15. Heater hose connection
16. Thermostat case
17. Thermostat case gasket
18. Transmission fluid cooler hose
connection
19. Water inlet pipe
>>
A
<<
20. O-ring
21. Water pipe gasket
Removal steps (Continued)
AC606081
Mating marks
AH
AC302615
Hose clip
Claw (Tip)
AE
AC509216
MB992042
AB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст