Mitsubishi Outlander GS45X. Manual — part 1239
OIL PAN AND TIMING CHAIN CASE
TSB Revision
ENGINE OVERHAUL <2.4L ENGINE>
11B-31
5. Tighten timing chain case mounting bolts to the specified
tightening torque.
Tightening torque
A: 24
± 4 N⋅m (18 ± 2 ft-lb)
B: 10
± 2 N⋅m (89 ± 17 in-lb)
C: 10
± 2 N⋅m (89 ± 17 in-lb)
D: 13
± 1 N⋅m (115 ± 8 in-lb)
.
>>B<< FRONT OIL SEAL INSTALLATION
1. Apply engine oil to the internal circumference of the oil seal.
2. Use special tool MB991448 to install the front oil seal on the
timing chain case.
.
>>C<< OIL PAN INSTALLATION
1. Completely remove liquid gasket adhering to the cylinder
block and oil pan.
2. Degrease the cylinder block and oil pan.
AK502378
A
A
A
A
A
A
B
B
B
B
B
B
C
D
AH
A: M8 × 30 mm (1.2 in)
B: M6 × 25 mm (1.0 in)
C: M6 × 25 mm (1.0 in)
D: M8 × 10 mm (0.4 in)
AK800005
1.5 – 2.5 mm
(0.06 – 0.09 in)
AC
MB991448
Chain case
Oil seal
MB991448
OIL PAN AND TIMING CHAIN CASE
TSB Revision
ENGINE OVERHAUL <2.4L ENGINE>
11B-32
CAUTION
Install the oil pan within three minutes after liquid gasket is
applied.
3. Apply liquid gasket of
φ2.5 ± 0.5 mm (0.10 ± 0.02 inch) of
thickness in diameter to the illustrated area of the oil pan.
Specified sealant:
Three bond 1217G or exact equivalent
4. Tighten the oil pan to the specified tightening torque.
Tightening torque:
M6:10
± 1 N⋅m (89 ± 17 in-lb)
M8: 29
± 2 N⋅m (21 ± 1 ft-lb)
.
>>D<< CYLINDER HEAD COVER INSTALLATION
1. Completely remove liquid gasket adhering to the cylinder
head cover, timing chain case and cylinder head.
2. Degrease the cylinder head cover, timing chain case and
cylinder head.
CAUTION
Install the cylinder head cover immediately after liquid gas-
ket is applied.
3. Appropriately use a minimum amount of sealant. Besides,
be careful not to allow sealant to squeeze out from the
application area.
Apply liquid gasket of 4 mm (0.15 inch) of thickness in
diameter.
Specified sealant:
Three bond 1217G or exact equivalent
4. Tighten the cylinder head cover to the tightening torque in
the order shown in the illustration.
Tightening torque: 3.0
± 1.0 N⋅m (27 ± 8 in-lb)
5. Then, tighten it to the specified tightening torque in the same
order.
Tightening torque: 5.5
± 0.5 N⋅m (49 ± 4 in-lb)
.
AK502377AD
1 mm
(0.04 in)
Ø2.5 ± 0.5 mm
(0.10 ± 0.02 in)
AK901127
Cylinder head
Timing chain case assembly
AD
φ 4.0 mm
(0.16 in)
φ 4.0 mm (0.16 in)
2.0 mm
(0.08 in)
2.0 mm
(0.08 in)
AK502760AF
10
16
15
14
17
18
1
3
4
11
12
9
5
2
6
7
8
13
OIL PAN AND TIMING CHAIN CASE
TSB Revision
ENGINE OVERHAUL <2.4L ENGINE>
11B-33
>>E<< OIL FILTER INSTALLATION
1. Clean the oil filter mounting surface of the ladder frame.
2. Apply engine oil to the O-ring of the oil filter.
CAUTION
Use special tool MB991396 to install the oil filter. Tighten-
ing it by hand causes oil leakage due to lack of torque.
3. Screw in the oil filter. When the O-ring contacts the mounting
surface, use a filter wrench to tighten it.
Tightening torque
3/4 turns (14
± 2 N⋅m [124 ± 17 in-lb])
AK305422 AD
AK502733AD
MB991396
TIMING CHAIN
TSB Revision
ENGINE OVERHAUL <2.4L ENGINE>
11B-34
TIMING CHAIN
REMOVAL AND INSTALLATION
M1113026600788
AKA00439
4
59 ± 5 N·m
44 ± 3 ft-lb
7
6
8
AB
Apply engine oil to
all moving parts
before installation.
10 ± 2 N·m
89 ± 17 in-lb
1
2
3
10 ± 2 N·m
89 ± 17 in-lb
10 ± 2 N·m
89 ± 17 in-lb
59 ± 5 N·m
44 ± 3 ft-lb
5
Removal steps
<<A>> >>D<<
1. Timing chain tensioner
2. Tensioner lever
3. Timing chain guide
>>C<<
4. Timing chain
<<B>> >>B<<
5. Exhaust V.V.T. sprocket bolt
6. Exhaust V.V.T. sprocket assembly
<<C>> >>A<<
7. Intake V.V.T. sprocket bolt
8. Intake V.V.T. sprocket assembly
Removal steps (Continued)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст