Mitsubishi Outlander GS45X. Manual — part 1347
MOLDINGS
TSB Revision
EXTERIOR
51-11
REMOVAL SERVICE POINTS
.
<<A>> ROOF DRIP MOLDING A/ CLIPS A, B, C
AND D REMOVAL
CAUTION
Remove the roof drip molding A from front to rear or oppo-
site direction in order.
1. Pull up the inner side of roof drip molding A rear end to
remove the clip A beneath it attached on the roof channel
<vehicles with roof rail>.
2. Twist the roof drip molding A rear end as shown in the
illustration. At the same time, pull the molding to vehicle
exterior from rear to front so that the clips B, C and D can be
remove from the front pillar. Then, remove the molding from
the body.
.
<<B>>CLIPS E POSITION MARKING TO FRONT
PILLAR
CAUTION
When replacing the clips E, mark installation position of
the clips to the front pillar before removing them.
.
AC711297AC
1
2
Roof drip molding A
Roof channel
Clip A
Vehicle
exterior
AC711301AD
AC711340AC
Clip E
Marking
MOLDINGS
TSB Revision
EXTERIOR
51-12
<<C>> ROOF DRIP MOLDING B/ CLIPS A
REMOVAL
CAUTION
Remove the roof drip molding B from front to rear or oppo-
site direction in order.
1. Pull up the roof drip molding B inner side to remove the clips
A beneath it attached on the roof channel.
2. Rotate the roof drip molding B together with clips A toward
vehicle exterior and remove them from roof channel.
INSTALLATION SERVICE POINTS
.
>>A<< CLIPS A AND E/ ROOF DRIP MOLDING A
INSTALLATION
CAUTION
Install the roof drip molding A from rear to front in order.
1. Remove the clip A from the roof drip molding A rear end and
attach it to the roof channel <vehicles with roof rail>.
2. When replacing the clips E, install new clips according to the
markings drawn at the removal time.
AC711297AD
1
2
Roof drip molding B
Roof channel
Clip A
Vehicle
exterior
AC711298AC
Clip A
Roof channel
Vehicle
exterior
AC711340AC
Clip E
Marking
MOLDINGS
TSB Revision
EXTERIOR
51-13
3. Install the roof drip molding A so that its front end is inserted
under the front deck garnish.
CAUTION
Make certain that the roof drip molding A rear end is not
overlapped with roof rail <vehicles with roof rail>.
4. Set the roof drip molding A (1) to the front pillar so that
cut-out (2) of the molding A (1) is engaged with clip E (3).
5. Push down the roof drip molding A securely so that it is
installed to the clip A <vehicles with roof rail> and clips E.
.
>>B<< CLIPS A/ ROOF DRIP MOLDING B
INSTALLATION
CAUTION
Install the roof drip molding B from front to rear or oppo-
site direction in order.
1. Remove the clips A from the roof drip molding B and attach
them to the roof channel.
2. Engage the projected portion of the roof drip molding B to
the 2 recessed portions of each clip A.
3. Push down the roof drip molding B securely so that it is
installed to the clips A on the roof channel.
AC711335AC
Front deck
garnish
Roof drip
molding A
AC711336AC
(1)
(1)
(3)
(3)
(2)
(2)
AC711298AC
Clip A
Roof channel
Vehicle
exterior
AC711300AC
Clip A
Roof drip
molding B
Vehicle
exterior
GARNISHES
TSB Revision
EXTERIOR
51-14
GARNISHES
SPECIAL TOOL
M1511000602195
REMOVAL AND INSTALLATION
M1511004100817
Tool
Tool number and
name
Supersession
Application
MB990784
Ornament remover
General service tool
Removal of garnishes
MB990784
AC900210
Section A – A
Section B – B
Section C – C
Clip
Bolt
4
2
AB
Clip
Nut
Liftgate molding
<Some models>
Clip
Nut
2
4
3
1
B
A
A
C
C
4
B
4.0 ± 2.0 N·m
35 ± 17 in-lb
4.0 ± 2.0 N·m
35 ± 17 in-lb
4.0 ± 2.0 N·m
35 ± 17 in-lb
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст