Mitsubishi Outlander GS45X. Manual — part 1150
DIAGNOSIS
TSB Revision
KEYLESS OPERATION SYSTEM (KOS)
42B-179
STEP 5. Retest the system
Check the scan tool screen when the key was not able to be
registered.
Q: Is the error message of scan tool screen "Abnormality
in key" ?
YES (Abnormality in key) : Carry out DTC B1A25: Key ID
unmatched and DTC B1A35: Transponder read error
(Refer to
<B1A35>).
Then, go to Step 7.
NO (ECU internal error) : Replace KOS-ECU and register
the ID codes (Refer to
STEP 6. Retest the system
Check that the keyless operation key can be registered.
Q: Is the keyless operation key that cannot be registered
using scan tool?
YES : Replace KOS-ECU and register the ID codes (Refer
to
NO : The procedure is complete.
STEP 7. Retest the system
Check that the keyless operation key can be registered.
Q: Is the keyless operation key that cannot be registered
using scan tool?
YES : Go to Step 8.
NO : The procedure is complete.
STEP 8. Check receiver antenna module connector C-30
and KOS-ECU connector C-102 for loose, corroded or
damaged terminals, or terminals pushed back in the
connector.
Q: Is the receiver antenna module connector C-30 and
KOS-ECU connector C-102 in good condition?
YES : Go to Step 9.
NO : Repair the defective connector.
STEP 9. Check the wiring harness between the receiver
antenna module connector C-30 (terminal Nos.1, 8, 12, 3, 5,
2, 4) and the KOS-ECU connector C-102 (terminal Nos.12,
32, 7, 9, 13, 11, 10).
• Check the all harness lines for open circuit and short circuit.
Q: Is the wiring harness between receiver antenna module
connector C-30 (terminal Nos.1, 8, 12, 3, 5, 2, 4) and the
KOS-ECU connector C-102 (terminal Nos.12, 32, 7, 9, 13,
11, 10) in good condition?
YES : Go to Step 10.
NO : Repair the wiring harness.
DIAGNOSIS
TSB Revision
KEYLESS OPERATION SYSTEM (KOS)
42B-180
STEP 10. Replace the receiver antenna module, and retest
the system.
Check that the keyless operation key can be registered.
Q: Is the keyless operation key that cannot be registered
using scan tool?
YES : Replace KOS-ECU and register the ID codes (Refer
to
NO : The procedure is complete.
Inspection Procedure 17: Engine does not start with emergency key (cranking but no initial
combustion).
.
TECHNICAL DESCRIPTION (COMMENT)
If the fuel injection does not work, KOS-ECU and the
MFI system may have a problem. This symptom is
not considered abnormal when the engine is started
by an keyless operation key that has not been regis-
tered.
.
TROUBLESHOOTING HINTS
• Malfunction of the MFI system
• Malfunction of KOS-ECU
• Malfunction of CAN bus line
• Malfunction of the transponder
• VIN not programmed
DIAGNOSIS
Required Special Tools:
• MB991958: Scan Tool (M.U.T.-III Sub Assembly)
• MB991824: Vehicle Communication Interface (V.C.I.)
• MB991827: M.U.T.-III USB Cable
• MB991910: M.U.T.-III Main Harness A (Vehicles with
CAN communication system)
STEP 1. Check the battery voltage.
Measure the battery voltage when cranking.
• The voltage should measure 8 volt or more.
Q: Is the measured voltage 8 volt or more?
YES : Go to Step 2.
NO : Check the battery (Refer to GROUP 54A
− Battery
test
).
DIAGNOSIS
TSB Revision
KEYLESS OPERATION SYSTEM (KOS)
42B-181
STEP 2. Using scan tool MB991958, diagnose the CAN bus
line.
CAUTION
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before con-
necting or disconnecting scan tool MB991958.
(1) Connect scan tool MB991958. Refer to "How to connect the
Scan Tool (M.U.T.-III)
(2) Turn the ignition switch to the "ON" position.
(3) Diagnose the CAN bus line.
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the CAN bus line found to be normal?
YES : Go to Step 3.
NO : Repair the CAN bus line (Refer to GROUP 54C,
).
STEP 3. Using scan tool MB991958, read the MFI system
diagnostic trouble code.
Check if DTC is set to the engine control module.
Q: Is the DTC set?
YES : Troubleshoot the MFI system (Refer to GROUP 13A,
<2.4L Engine> or GROUP 13B,
<3.0L Engine>).
NO : Go to Step 4.
STEP 4. Using scan tool MB991958, read the KOS-ECU
diagnostic trouble code.
Check if DTC is set to the KOS.
Q: Is the DTC set?
.
NO : Go to Step 5.
STEP 5. Check that the engine starts.
Q: Does the engine start?
YES : The procedure is complete.
NO : Refer to GROUP 13A , Diagnosis
<2.4L
Engine> or GROUP 13B , Diagnosis
Engine>. When the cause of the failure cannot be
tracked down by the troubleshooting in GROUP 13A
<2.4L Engine> or GROUP 13B <3.0L Engine>,
replace KOS-ECU and register the ID codes (Refer to
).
ZC501967
AC404789
AC701411AB
MB991824
MB991827
MB991910
Data link
connector
DIAGNOSIS
TSB Revision
KEYLESS OPERATION SYSTEM (KOS)
42B-182
Inspection Procedure 18: Power door locks with selective unlocking does not work.
CAUTION
Before replacing the ECU, ensure that the power
supply circuit, the ground circuit and the com-
munication circuit are normal.
.
COMMENT ON TROUBLE SYMPTOM
When the keyless entry function and door entry func-
tion operate normally, but there is an error to only the
power door locks with selective unlocking,
ETACS-ECU may have a problem. In addition, it is
possible that the function has been set to "all doors
unlock" by the customization function.
.
PROBABLE CAUSES
• Malfunction of ETACS-ECU
• Damaged wiring harness and connectors
DIAGNOSIS
STEP 1. Check the customization
Q: Are the power door locks with selective unlocking
enabled by the customization function?
YES : Go to Step 2
NO : Set the power door locks with selective unlocking to
"Enabled" by using the customization function. Refer
to
STEP 2. Power door locks with selective unlocking
operation check
Check that the power door locks with selective unlocking oper-
ate normally by means of the keyless entry function or door
entry function.
Q: Is the check result normal?
YES : Go to Step 5
NO (Does not work by means of keyless entry function)
:
Go to Step 3
NO (Does not work by means of door entry function) :
Go to Step 4
NO (Does not work by means of either functions) : Go to
Step 5
STEP 3. Keyless entry system operation check
Press the unlock switch of the keyless operation key and check
that only the driver's door is unlocked. Then, press the unlock
switch once again within 2 seconds after that to check that the
front passenger's door, rear doors, and liftgate are unlocked.
Q: Does the keyless entry function work normally?
YES : Go to Step 5
NO (Only the driver's door is not unlocked.) : Replace
ETACS-ECU.
NO (The driver's door, front passenger's door, rear
doors, and tailgate are not unlocked.) : Refer to
Inspection Procedure 12: "Keyless entry function
does not work
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст