Mitsubishi Outlander GS45X. Manual — part 501
CAMSHAFT AND VALVE STEM SEAL
TSB Revision
ENGINE MECHANICAL <3.0L ENGINE>
11C-41
>>E<< ROCKER COVER INSTALLATION
Tighten the bolts in order of the numbers shown in the illustra-
tion.
.
>>F<< CAMSHAFT OIL SEAL INSTALLATION
1. Apply engine oil to the camshaft oil seal lip.
2. Use special tools MD998713 and MD998777 to press-fit the
camshaft oil seal.
.
>>G<< CAMSHAFT SPROCKET INSTALLATION
1. Use special tools MB990767 and MD998719 in the same
way as during removal to hold the camshaft sprocket.
2. Tighten the camshaft sprocket mounting bolt to the specified
torque.
Tightening torque: 90
± 10 N⋅m (66 ± 7 ft-lb)
.
AC703030
Right bank
Left bank
1
2
3
4
5
6
1
2
3
4
5
6
AB
AC703083
<Right bank>
MD998713
Oil seal
Camshaft
AB
AC703082
MD998713
MD998777
Camshaft
Oil seal
<Left bank>
AB
AC703052
MB990767
MD998719
AB
CAMSHAFT AND VALVE STEM SEAL
TSB Revision
ENGINE MECHANICAL <3.0L ENGINE>
11C-42
>>H<< ENGINE OIL PRESSURE SWITCH
INSTALLATION
Apply the specified sealant to the thread of the engine oil pres-
sure switch.
Specified sealant: ThreeBond 1141J or equivalent
.
>>I<< O-RING/ENGINE OIL CONTROL VALVE
INSTALLATION
CAUTION
• Never re-use the O-ring.
• Before installing O-ring, wind sealing tape around the
oil passages cut-out area of engine oil control valve, to
prevent damage. If the O-ring is damaged, it can cause
an oil leak.
1. Apply a small amount of engine oil to the O-ring and then
install it to the engine oil control valve.
2. Install the engine oil control valve to the cylinder head.
3. Tighten the engine oil control valve.
Tightening torque: 11
± 1 N⋅m (97 ± 8 in-lb)
AC703070
5 mm
(0.20 in)
1 mm
(0.04 in)
AB
AC703080
Tape
AB
OIL PAN AND OIL STRAINER
TSB Revision
ENGINE MECHANICAL <3.0L ENGINE>
11C-43
OIL PAN AND OIL STRAINER
REMOVAL AND INSTALLATION
M1112008301178
Pre-removal and Post-installation Operation
• Engine Room Under Cover Front Removal and Installa-
tion (Refer to GROUP 51, Under Cover
P.51-23
).
• Engine Oil Draining and Refilling (Refer to GROUP 12,
On-vehicle Service
− Engine Oil Replacement
).
AC703044
1
2
3
4
5
6
7
8
9
20 ± 5 N·m
15 ± 3 ft-lb
9.5 ± 2.5 N·m
85 ± 22 in-lb
36 ± 9 N·m
27 ± 6 ft-lb
36 ± 9 N·m
27 ± 6 ft-lb
9.5 ± 2.5 N·m
85 ± 22 in-lb
11 ± 1 N·m
93 ± 13 in-lb
39 ± 5 N·m
29 ± 3 ft-lb
N
N
AC
Removal steps
1.
Engine oil pan drain plug
>>C<<
2.
Engine oil pan drain plug gasket
3.
Starter connector and terminal
connection
4.
Starter assembly
<<A>> >>B<<
5.
Engine lower oil pan
•
Front exhaust pipe (Refer to
GROUP 15, Exhaust Pipe and
Main Muffler
P.15-25
)
>>A<<
6.
Cover
<<B>>
•
A/C compressor assembly (Refer to
Removal steps (Continued)
OIL PAN AND OIL STRAINER
TSB Revision
ENGINE MECHANICAL <3.0L ENGINE>
11C-44
Required Special Tool:
MD998727: Oil Pan FIPG Cutter
REMOVAL SERVICE POINTS
.
<<A>> ENGINE LOWER OIL PAN REMOVAL
Insert the special tool MD998727 into the groove shown in the
illustration. Strike and slide it and then cut the liquid gasket.
.
<<B>> A/C COMPRESSOR ASSEMBLY REMOVAL
1. Remove the A/C compressor from the A/C compressor
bracket with the hose still attached.
2. Place the removed A/C compressor where it will not be a
hindrance when removing and installing the engine oil pan,
and secure it with a cord or wire.
.
<<C>> ENGINE UPPER OIL PAN REMOVAL
1. Remove the engine upper oil pan mounting bolts.
CAUTION
Do not use special tool MD998727. The engine upper oil
pan is made of aluminum and this tool will damage it.
2. Screw in the bolt (M10
× 1.5) into bolt hole A in the location
shown. Then lift the upper oil pan and remove it.
•
A/C compressor bracket (Refer to
GROUP 55A, Compressor
Assembly
)
<<C>> >>A<<
7.
Engine upper oil pan
8.
Oil strainer
9.
Oil strainer gasket
Removal steps (Continued)
AC703057
MD998727
Groove
AB
AC703054
A
AB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст