Mitsubishi Outlander GS45X. Manual — part 502
OIL PAN AND OIL STRAINER
TSB Revision
ENGINE MECHANICAL <3.0L ENGINE>
11C-45
INSTALLATION SERVICE POINTS
.
>>A<< ENGINE UPPER OIL PAN/COVER INSTAL-
LATION
1. Remove sealant from the oil pan and cylinder block mating
surfaces.
2. Apply a bead of the sealant to the cylinder block mating
surface of the engine oil pan as shown.
Specified sealant: ThreeBond 1227D or equivalent
NOTE: Install the engine lower oil pan immediately after
applying sealant.
3. Assemble the oil pan to the cylinder block to the engine
upper oil pan.
4. Install the bolts to the engine upper oil pan and cover as
shown, and tighten them to the specified torque.
Tightening torque: 9.5
± 2.5 N⋅m (85 ± 22 in-lb)
.
AC703031
Ø2 mm or Ø3 mm
(Ø0.08 in or Ø0.12 in)
AB
AC703032AB
Bolt specifications
Thread diameter × Length mm
M6 × 20
M6 × 20
M6 × 20
M6 × 10
M6 × 124
M6 × 124
OIL PAN AND OIL STRAINER
TSB Revision
ENGINE MECHANICAL <3.0L ENGINE>
11C-46
>>B<< ENGINE LOWER OIL PAN INSTALLATION
1. Remove sealant from the engine lower oil pan and engine
upper oil pan.
2. Degrease the sealant-coated surface and the engine lower
oil pan mating surface.
3. Apply a bead of the sealant to the mating surface of the
engine lower oil pan as shown.
Specified sealant: ThreeBond 1227D or equivalent
NOTE: Install the engine lower oil pan immediately after
applying sealant.
4. Assemble the engine lower oil pan to the engine upper oil
pan.
CAUTION
After the installation, until a sufficient period of time (one
hour or more) elapses, do not apply the engine oil or water
to the sealant application area or start the engine.
5. Install the bolts to the lower oil pan as shown, and tighten
them to the specified torque.
Tightening torque: 9.5
± 2.5 N⋅m (85 ± 22 in-lb)
.
>>C<< ENGINE OIL PAN DRAIN PLUG
INSTALLATION
Replace the gasket with a new gasket. Install the new gasket in
the direction shown in the illustration.
AC703033AB
Ø2 mm or Ø3 mm
(Ø0.08 in or
Ø0.12 in)
AC703034
Bolt specifications
Thread diameter × Length mm
M6 × 10
M6 × 10
M6 × 91
M6 × 91
M6 × 10
AB
AC703071
Engine lower
oil pan side
AB
CRANKSHAFT FRONT OIL SEAL
TSB Revision
ENGINE MECHANICAL <3.0L ENGINE>
11C-47
INSPECTION
M1112008400224
• Check the engine oil pan for cracks.
• Check the engine oil pan sealant-coated surface for dam-
age and deformation.
• Check the oil strainer for cracked, clogged or damaged wire
net and pipe.
CRANKSHAFT FRONT OIL SEAL
REMOVAL AND INSTALLATION
M1112003400661
Required Special Tool:
• MD998382: Crankshaft Front Oil Seal Installer
Pre-removal and Post-installation Operation
• Timing Belt Removal and Installation (Refer to
AC703045
Engine oil
3
1
2
3
N
AB
Removal steps
>>B<<
1.
Crankshaft sprocket
2.
Key
>>A<<
3.
Crankshaft front oil seal
Removal steps (Continued)
CRANKSHAFT FRONT OIL SEAL
TSB Revision
ENGINE MECHANICAL <3.0L ENGINE>
11C-48
INSTALLATION SERVICE POINTS
.
>>A<< CRANKSHAFT FRONT OIL SEAL INSTAL-
LATION
1. Apply a small amount of engine oil to the oil seal lip and then
insert the o-ring.
2. Using special tool MD998382, tap the oil seal into the front
case.
.
>>B<< CRANKSHAFT SPROCKET INSTALLATION
Clean the crankshaft and crankshaft sprocket, and mount
them.
AC703081
MD998382
Crankshaft
Oil seal
AB
AC703038
: Clean
Crankshaft sprocket
Crankshaft
AB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст