Mitsubishi Outlander GS45X. Manual — part 1215
GENERATOR AND DRIVE BELT
TSB Revision
ENGINE OVERHAUL <3.0L ENGINE>
11D-13
REMOVAL SERVICE POINT
.
<<A>> CRANKSHAFT BOLT REMOVAL
1. Using special tool MD998781, hold the drive plate.
2. Remove the crankshaft bolt.
INSTALLATION SERVICE POINT
.
>>A<< GENERATOR INSTALLATION
1. Temporarily tighten the alternator to the alternator bracket.
2. In accordance with the tightening order shown in the
illustration, tighten the installation bolts for the alternator to
the specified torque.
Tightening torque: 47
± 11 N⋅m (35 ± 7 ft-lb)
.
>>B<< CRANKSHAFT BOLT INSTALLATION
1. Using special tool MD998781, hold the drive plate.
AK600940AC
MD998781
AK600845
1
2
3
AC
AK600940AC
MD998781
GENERATOR AND DRIVE BELT
TSB Revision
ENGINE OVERHAUL <3.0L ENGINE>
11D-14
2. Wipe the dirt on the crankshaft pulley washer using a rag.
3. Using a rag, wipe the dirt on the crankshaft pulley, the front
flange, the crankshaft sprocket, the thread hole of the
crankshaft and then remove the grease.
4. Install the front flange and crankshaft pulley.
5. Apply an appropriate and minimum amount of engine oil to
the threads of crankshaft pulley centre bolt and lower part of
the flange.
6. Install the crankshaft pulley washer to the crankshaft pulley
centre bolt.
7. Tighten the crankshaft pulley centre bolt to 200 N
⋅m (148
ft-lb).
8. Loosen the crankshaft pulley centre bolt fully.
9. Tighten the crankshaft pulley centre bolt to 110 N
⋅m (81
ft-lb).
10.Make a paint mark on the crankshaft bolt.
CAUTION
• When the tightening angle is smaller than the specified
tightening angle, the appropriate tightening capacity
cannot be secured.
• When the tightening angle is larger than the specified
tightening angle, remove the bolt to start from the
beginning again according to the procedure.
11.Make a paint mark on the bolt end at a position 60 degrees
from the paint mark made on the crankshaft pulley in the
direction of tightening the crankshaft bolt.
12.Turn the crankshaft bolt another 60 degrees and make sure
that the paint marks on the crankshaft pulley and crankshaft
bolt are aligned.
AK602913
AG
Engine front
Crankshaft
pulley centre bolt
Crankshaft
pulley washer
Crankshaft pulley
Crankshaft sprocket
Front frange
: Wipe clean with a rag.
: Wipe clean with a rag and degrease.
: Wipe clean with a rag, degrease and
apply a small amount of engine oil.
Crankshaft
AK600939
60˚
AC
Crankshaft pulley
Crankshaft bolt
Paint mark
INTAKE MANIFOLD PLENUM AND THROTTLE BODY ASSEMBLY
TSB Revision
ENGINE OVERHAUL <3.0L ENGINE>
11D-15
INTAKE MANIFOLD PLENUM AND
THROTTLE BODY ASSEMBLY
REMOVAL AND INSTALLATION
M1113003200176
AK900047AE
16
5
8
9
10
11
7
6
3
4
13
1
12
2
17
15
14
18
23 ± 6 N·m
17 ± 4 ft-lb
23 ± 6 N·m
17 ± 4 ft-lb
23 ± 6 N·m
17 ± 4 ft-lb
22 ± 1 N·m
16 ± 1 ft-lb
23 ± 6 N·m
17 ± 4 ft-lb
23 ± 6 N·m
17 ± 4 ft-lb
23 ± 6 N·m
17 ± 4 ft-lb
5.0 ± 1.0 N·m
45 ± 8 in-lb
5.0 ± 1.0 N·m
45 ± 8 in-lb
Removal steps
1. Exhaust gas recirculation pipe
>>E<<
2. Exhaust gas recirculation pipe gasket
3. Exhaust gas recirculation pipe gasket
4. Harness bracket
5. Throttle body
6. Throttle body gasket
7. Vacuum hose
8. Solenoid valve
9. O-ring
10. Boost sensor
11. O-ring
12. Purge hose
Removal steps (Continued)
INTAKE MANIFOLD PLENUM AND THROTTLE BODY ASSEMBLY
TSB Revision
ENGINE OVERHAUL <3.0L ENGINE>
11D-16
INSTALLATION SERVICE POINT
.
>>A<< INTAKE MANIFOLD PLENUM STAY, REAR
INSTALLATION
1. After temporarily tightening the rear intake manifold plenum
stay with the installation bolts, check that the intake manifold
fastens securely to the cylinder head.
2. Tighten the rear intake manifold plenum stay to the specified
torque.
Tightening torque: 23
± 6 N⋅m (17 ± 4 ft-lb)
.
>>B<< INTAKE MANIFOLD PLENUM STAY, FRONT
INSTALLATION
1. After temporarily tightening the front manifold plenum stay
with the installation bolts, check that the intake manifold
fastens securely to the cylinder head.
2. Tighten the front manifold plenum stay to the specified
torque.
Tightening torque: 23
± 6 N⋅m (17 ± 4 ft-lb)
.
>>C<< THROTTLE BODY STAY INSTALLATION
1. After temporarily tightening the throttle body stay with the
installation bolts, check that the throttle body fastens
securely to the cylinder head.
2. Tighten the throttle body stay to the specified torque.
Tightening torque: 23
± 6 N⋅m (17 ± 4 ft-lb)
.
13. Throttle body stay
14. Engine hanger, right
15. Intake manifold plenum stay, front
16. Intake manifold plenum stay, rear
17. Intake manifold plenum
18. Intake manifold plenum gasket
Removal steps (Continued)
AK900036
AC
Intake manifold
plenum stay, rear
AK900037AC
Intake manifold
plenum stay, front
AK900038 AC
Throttle body
stay
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст