Mitsubishi Outlander GS45X. Manual — part 1557
PARKING BRAKE CABLE
TSB Revision
PARKING BRAKES
36-13
PARKING BRAKE CABLE
REMOVAL AND INSTALLATION
M1361001901562
Pre-removal operation
• Rear Floor Console Assembly Removal (Refer to GROUP
52A
• Second Seat Assembly Removal (Refer to GROUP 52A −
Second Seat Assembly
• Shoe and Lining Assembly Removal (Refer to
<2.4L Engine: 5 persons seat> or
<2.4L Engine:
7 persons seat, 3.0L Engine>).
Post-installation operation
• Shoe and Lining Assembly Installation (Refer to
<2.4L Engine: 5 persons seat> or
<2.4L Engine:
7 persons seat, 3.0L Engine>).
• Second Seat Assembly Installation (Refer to GROUP 52A
− Second Seat Assembly
• Parking Brake Lever Stroke Check and Adjustment (Refer
).
• Rear Floor Console Assembly Installation (Refer to
GROUP 52A
− Rear Floor Console Assembly
).
• Parking brake lining seating procedure (Refer to
).
AC709969
2
AE
2
3
2
2
3
1
1
13 ± 2 N·m
111 ± 22 in-lb
13 ± 2 N·m
111 ± 22 in-lb
13 ± 2 N·m
111 ± 22 in-lb
13 ± 2 N·m
111 ± 22 in-lb
11 ± 2 N·m
98 ± 17 in-lb
11 ± 2 N·m
98 ± 17 in-lb
11 ± 2 N·m
98 ± 17 in-lb
11 ± 2 N·m
98 ± 17 in-lb
11 ± 2 N·m
98 ± 17 in-lb
11 ± 2 N·m
98 ± 17 in-lb
<2.4L Engine: 5 persons seat>
<2.4L Engine: 7 persons seat, 3.0L Engine>
Removal steps
•
Release the parking brake lever.
•
Loosen the adjusting nut.
>>
A
<< 1.
Parking brake rear cable assembly
connection
2.
Clip
3.
Parking brake rear cable assembly
Removal steps (Continued)
PARKING BRAKE CABLE
TSB Revision
PARKING BRAKES
36-14
INSTALLATION SERVICE POINT
.
>>A<< PARKING BRAKE REAR CABLE ASSEM-
BLY CONNECTION INSTALLATION
CAUTION
Check that the equalizer and the parking brake rear cable
assembly are connected correctly. If the parking brake is
applied with the equalizer and the parking brake rear cable
assembly connected improperly, the equalizer may be
damaged.
Connect the parking brake rear cable assembly to the equalizer
as shown in the figure.
AC903102 AF
Equalizer
Equalizer
Parking brake
rear cable assembly
A
A
Section A - A
Parking brake
rear cable assembly
PARKING BRAKE LINING AND DRUM
TSB Revision
PARKING BRAKES
36-15
PARKING BRAKE LINING AND DRUM
REMOVAL AND INSTALLATION <2.4L ENGINE: 5 PERSONS SEAT>
M1361002500939
Post-installation Operation
• Parking Brake Lever Stroke Check and Adjustment (Refer
to
).
• Parking Brake Lining Seating Procedure (Refer to
AC803237AB
2
5
6 4
9
20
19
13
12
8
14
11
7
11
15
3
N
10
17
18
16
1
12
13
14
16
Backing plate
8
55 ± 5 N·m
41 ± 3 ft-lb
Removal steps
•
Release the parking brake lever.
1.
Plug
<<A>>
2.
Rear brake caliper assembly
3.
Rear brake disk
>>D<<
4.
Shoe-to-anchor spring
>>D<<
5.
Shoe-to-anchor spring
6.
Shoe guide plate
7.
Adjusting wheel spring
>>C<<
8.
Adjuster assembly
9.
Strut
10. Strut shoe-to-spring
11. Shoe hold down pin
12. Shoe hold down cup
13. Shoe hold down spring
14. Shoe and lining assembly
15. Parking brake rear cable assembly
connection
16. Shoe and lever assembly
<<B>> >>B<<
17. Retainer
>>A<<
18. Wave washer
19. Parking lever
20. Shoe and lining assembly
Removal steps (Continued)
PARKING BRAKE LINING AND DRUM
TSB Revision
PARKING BRAKES
36-16
REMOVAL SERVICE POINTS
.
<<A>> REAR BRAKE CALLIPER ASSEMBLY
REMOVAL
1. Remove the rear brake caliper assembly with the brake
hose.
2. Secure the removed rear brake caliper assembly with a wire
or other similar material at a position where it will not
interfere with the removal and installation operations.
.
<<B>> RETAINER REMOVAL
Use a flat-tipped screwdriver or a similar tool to open up the
retainer joint. Then remove the retainer.
INSTALLATION SERVICE POINTS
.
>>A<< WAVE WASHER INSTALLATION
Install the wave washer in the direction shown in the illustration.
.
>>B<< RETAINER INSTALLATION
Use pliers or a similar tool to close the retainer end onto the
pin.
.
AC000924AF
Pin of shoe assembly
Retainer
AC304675AC
Shoe and lining assembly
Retainer
Parking lever
Wave washer
AC000926
Pin of shoe assembly
Retainer
AH
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст