Mitsubishi Outlander GS45X. Manual — part 1558
PARKING BRAKE LINING AND DRUM
TSB Revision
PARKING BRAKES
36-17
>>C<< ADJUSTER ASSEMBLY INSTALLATION
Install the adjuster assemblies. The shoe adjusting bolt should
be mounted to the rear of the vehicle for the right wheel, and to
the front of the vehicle for the left wheel.
.
>>D<< SHOE-TO-ANCHOR SPRING
INSTALLATION
The shoe-to-anchor springs are not interchangeable because
their spring loads are different. The one with blue paint mark
should be installed to the front of the vehicle, and the other with
yellow paint to the rear of the vehicle, respectively.
AC801849AB
Shoe adjusting bolt
Shoe adjusting bolt
<Right side wheel>
<Left side wheel>
Front of the vehicle
Rear of the vehicle
AC706198 AB
Front of the vehicle
Blue paint
Yellow paint
Blue paint
Yellow paint
<Right side wheel>
<Left side wheel>
PARKING BRAKE LINING AND DRUM
TSB Revision
PARKING BRAKES
36-18
REMOVAL AND INSTALLATION <2.4L ENGINE: 7 PERSONS SEAT, 3.0L ENGINE>
M1361002500940
Post-installation Operation
• Parking Brake Lever Stroke Check and Adjustment (Refer
to
).
• Parking Brake Lining Seating Procedure (Refer to
AC801680
2
3
1
5
4
6
7
8
AB
9
10
11
12
13
14
15
14
16
16
17
18
19
20
11
12
N
8
Backing plate
58 ± 7 N·m
43 ± 5 ft-lb
Removal steps
•
Release the parking brake lever.
1.
Plug
<<A>>
2.
Rear brake caliper assembly
3.
Rear brake disk
>>D<<
4.
Shoe-to-anchor spring
>>D<<
5.
Shoe-to-anchor spring
6.
Shoe guide plate
7.
Adjusting wheel spring
>>C<<
8.
Adjuster assembly
9.
Strut
10. Strut shoe-to-spring
11. Shoe hold down cup
12. Shoe hold down spring
13. Shoe hold down pin
14. Shoe and lining assembly
15. Parking brake rear cable assembly
connection
16. Shoe and lever assembly
<<B>> >>B<<
17. Retainer
>>A<<
18. Wave washer
19. Parking lever
20. Shoe and lining assembly
Removal steps (Continued)
PARKING BRAKE LINING AND DRUM
TSB Revision
PARKING BRAKES
36-19
REMOVAL SERVICE POINTS
.
<<A>> REAR BRAKE CALLIPER ASSEMBLY
REMOVAL
1. Remove the rear brake caliper assembly with the brake
hose.
2. Secure the removed rear brake caliper assembly with a wire
or other similar material at a position where it will not
interfere with the removal and installation operations.
.
<<B>> RETAINER REMOVAL
Use a flat-tipped screwdriver or a similar tool to open up the
retainer joint. Then remove the retainer.
INSTALLATION SERVICE POINTS
.
>>A<< WAVE WASHER INSTALLATION
Install the wave washer in the direction shown in the illustration.
.
>>B<< RETAINER INSTALLATION
Use pliers or a similar tool to close the retainer end onto the
pin.
.
AC000924AF
Pin of shoe assembly
Retainer
AC304675AC
Shoe and lining assembly
Retainer
Parking lever
Wave washer
AC000926
Pin of shoe assembly
Retainer
AH
PARKING BRAKE LINING AND DRUM
TSB Revision
PARKING BRAKES
36-20
>>C<< ADJUSTER ASSEMBLY INSTALLATION
Install the adjuster assemblies. The shoe adjusting bolt should
be mounted to the rear of the vehicle for the right wheel, and to
the front of the vehicle for the left wheel.
.
>>D<< SHOE-TO-ANCHOR SPRING
INSTALLATION
The shoe-to-anchor springs are not interchangeable because
their spring loads are different. The one with blue paint mark
should be installed to the front of the vehicle, and the other with
yellow paint to the rear of the vehicle, respectively.
AC706498AB
Shoe adjusting bolt
Shoe adjusting bolt
<Right side wheel>
<Left side wheel>
Front of the vehicle
Rear of the vehicle
AC706198 AB
Front of the vehicle
Blue paint
Yellow paint
Blue paint
Yellow paint
<Right side wheel>
<Left side wheel>
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст