Mitsubishi Outlander GS45X. Manual — part 1748
A/T FLUID COOLER LINE
TSB Revision
AUTOMATIC TRANSAXLE
23C-297
A/T FLUID COOLER LINE
REMOVAL AND INSTALLATION
M1231036800117
Pre-removal and post-installation operation
• Engine room under cover front, engine room side cover
(Refer to GROUP 51
− Under Cover
.)
• Front bumper extension A, B, transmission fluid cooler
duct (Refer to GROUP 51
− Front Bumper Assembly
.)
• Engine coolant draining and refilling (Refer to GROUP 14
− On-vehicle Service − Engine Coolant Replacement
• Transmission fluid draining and refilling (Refer to
AC607810AC
1
2
3
4
5
6
7
8
11
13
12
10
9
11 ± 2 N·m
97 ± 17 ft-lb
11 ± 2 N·m
97 ± 17 ft-lb
23 ± 3 N·m
17 ± 2 ft-lb
23 ± 3 N·m
17 ± 2 ft-lb
22 ± 3 N·m
16 ± 2 ft-lb
A/T FLUID COOLER LINE
TSB Revision
AUTOMATIC TRANSAXLE
23C-298
THERMO VALVE CHECK
M1231036900073
.
1. Obtain a container filled with water and place the thermo
valve in it with a stick (approximately 6 mm in diameter)
inserted. Gradually warm up the water while stirring, and
check that the thermo valve opening temperature is within
the standard value. The stick rises when the thermo valve
opens.
Standard value: 75
± 1.5°C (167 ± 34.7 °F)
2. Warm up the water to the full-open temperature of the
thermo valve, and check that the valve lift amount is within
the standard value.
Standard value: Full-open temperature 95
°C (203°F)
or more
Valve lift amount when it is fully opened: 3 mm or
more
NOTE: Measure the height of the fully closed valve in
advance, and then measure the valve height at fully open
temperature to calculate the lift amount.
Removal steps
1.
Water return hose A
2.
Water return tube
3.
Water return hose B
4.
Water feed hose A
5.
Water feed tube
6.
Water feed hose B
7.
Thermo valve assembly
8.
Water feed hose C
9.
Transmission fluid cooler hose
assembly
10.
Transmission fluid cooler bracket A
11.
Transmission fluid cooler bracket B
12.
Transmission fluid cooler bracket C
13.
Transmission fluid cooler assembly
Removal steps (Continued)
AC607811
AB
Thermo valve
Stick (6 mm in diameter)
23D-1
GROUP 23D
AUTOMATIC
TRANSAXLE
OVERHAUL
CONTENTS
TRANSAXLE MODELS . . . . . . . . . . .
GENERAL SPECIFICATIONS . . . . . .
SERVICE SPECIFICATIONS. . . . . . .
TORQUE SPECIFICATIONS . . . . . . .
ADJUSTING PLATE, SNAP RING,
SHIM, SPACER, NEEDLE BEARING,
THRUST WASHER AND
BEARING RACE . . . . . . . . . . . . . . . .
SEALANTS . . . . . . . . . . . . . . . . . . . .
LUBRICANTS . . . . . . . . . . . . . . . . . . .
SPECIAL TOOLS . . . . . . . . . . . . . . . .
TRANSAXLE. . . . . . . . . . . . . . . . . . . .
DISASSEMBLY AND ASSEMBLY . . . . . . .
SIDE COVER . . . . . . . . . . . . . . . . . . .
DISASSEMBLY AND ASSEMBLY . . . . . . .
DIFFERENTIAL. . . . . . . . . . . . . . . . . .
DISASSEMBLY AND ASSEMBLY . . . . . . .
TRANSFER . . . . . . . . . . . . . . . . . . . . .
DISASSEMBLY AND ASSEMBLY . . . . . . .
TRANSAXLE MODELS
TSB Revision
AUTOMATIC TRANSAXLE OVERHAUL
23D-2
TRANSAXLE MODELS
M1233000101785
GENERAL SPECIFICATIONS
M1233000201232
SERVICE SPECIFICATIONS
M1233000300872
Transaxle model
Engine model
Vehicle model
F6AJA-1-F1Z
6B31
CW6WX
W6AJA-1-F1ZA
6B31
CW6WX
W6AJA-1-F1ZB
6B31
CW6WX
Item
Specifications
Transaxle model
F6AJA
W6AJA
Transaxle type
Electronically controlled 6-speed full-automatic
Torque converter
Type
3-element with torque converter clutch
Stall torque ratio 1.96
Lock-up
Present
Transaxle gear
ratio
1st
4.199
2nd
2.405
3rd
1.583
4th
1.161
5th
0.855
6th
0.685
Reverse
3.457
Final gear ratio
3.571
Transfer type
−
Center differential type full-time
4WD
Transfer gear ratio
−
0.425
Item
Standard value mm (in)
Reduction gear preload
0.16
− 0.22 (0.006 − 0.009)
Differential preload
0.19
− 0.25 (0.008 − 0.010)
Low-reverse brake clearance
1.9
− 2.2 (0.07 − 0.09)
2-6 brake clearance
1.9
− 2.2 (0.07 − 0.09)
Reduction sun gear end play
0.4
− 0.7 (0.02 − 0.03)
Side cover end play
0.70
− 1.05 (0.028 − 0.041)
Drum support end play
0
− 0.35 (0 − 0.014)
3-5 reverse clutch end play
0.55
− 0.85 (0.022 − 0.034)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст