Mitsubishi Outlander GS45X. Manual — part 1472

SRS AIR BAG DIAGNOSIS

TSB Revision

SUPPLEMENTAL RESTRAINT SYSTEM (SRS)

52B-383

DTC B1CB2: Occupant Classification-ECU Parameter Table Incompatible

DTC B2212: Occupant Classification-ECU Internal Failure

DTC B2250: Occupant Classification-ECU not Parameter Flash Required

DTC B2262: Occupant Classification-ECU Electrostatic Discharge Event Detected

CAUTION

If DTC B1CB2, B2212, B2250, B2262 is set in the
occupant classification-ECU, always diagnose
the CAN main bus lines.

.

TROUBLE JUDGMENT

The above DTC is set if an abnormality is detected in
the circuit inside the occupant classification-ECU.

.

TROUBLESHOOTING HINTS

Malfunction of the occupant classification-ECU

DIAGNOSIS

Required Special Tools:

• MB991958: Scan Tool (M.U.T.-III Sub Assembly)

• MB991824: Vehicles Communication Interface (V.C.I.)

• MB991827: M.U.T.-III USB Cable

• MB991910: M.U.T.-III Main Harness A (Vehicles with

CAN communication system)

STEP 1. Using scan tool MB991958, diagnose the CAN bus
line.

CAUTION

To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before con-
necting or disconnecting scan tool MB991958.
(1) Connect scan tool MB991958. Refer to "How to connect the

scan tool

P.52B-28

."

(2) Turn the ignition switch to the "ON" position.
(3) Diagnose the CAN bus line.
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the CAN bus line found to be normal?

YES : Go to Step 2.
NO : Repair the CAN bus line (Refer to GROUP 54C,

Diagnosis

P.54C-17

).

ZC501967

AC404789

AC701411AB

MB991824

MB991827

MB991910

Data link
connector

SRS AIR BAG DIAGNOSIS

TSB Revision

SUPPLEMENTAL RESTRAINT SYSTEM (SRS)

52B-384

STEP 2. Recheck for diagnostic trouble code.
Check again if the DTC is set.
(1) Erase the DTC.
(2) Turn the ignition switch from "LOCK" (OFF) position to "ON"

position.

(3) Check if DTC is set.
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the DTC set?

YES : Replace the passenger seat cushion frame assembly

(Refer to GROUP 52A, Front Seat Assembly

P.52A-17

).

NO : There is an intermittent malfunction such as poor

engaged connector(s) or open circuit (Refer to
GROUP 00, How to Cope with Intermittent
Malfunction

P.00-15

).

SRS AIR BAG DIAGNOSIS

TSB Revision

SUPPLEMENTAL RESTRAINT SYSTEM (SRS)

52B-385

DTC B210D: Battery Voltage Low

DTC B210E: Battery Voltage High

AC803418

FUSIBLE
LINK

34

POWER
SUPPLY

OCCUPANT
CLASSIFICATION-ECU

FRONT SEAT
ASSEMBLY (RH)

Occupant Classification-ECU Power Supply Circuit

ETACS-ECU

AB

AC901079

Connector: D-34-2

AP

ACA02655AJ

Connectors: C-309, C-315

C-315

C-309 (B)

SRS AIR BAG DIAGNOSIS

TSB Revision

SUPPLEMENTAL RESTRAINT SYSTEM (SRS)

52B-386

CAUTION

If DTC B210D, B210E is set in the occupant clas-
sification-ECU, always diagnose the CAN main
bus lines.

.

TROUBLE JUDGMENT

The occupant classification-ECU sets DTC B210D if
the power supply fuse voltage decreases to the
specified value or less, and sets DTC B210E if the
power supply fuse voltage increases to the specified
value or more.

.

TECHNICAL DESCRIPTION (COMMENT)

The power supply fuse or the occupant classifica-
tion-ECU may have a problem.

.

TROUBLESHOOTING HINTS

• The power supply fuse may be defective.

• The occupant classification-ECU may be defec-

tive.

• The battery may be defective.

• The generator may be defective.

• The wiring harness or connectors may have

loose, corroded, or damaged terminals, or termi-
nals pushed back in the connector

DIAGNOSIS

Required Special Tools:

• MB991958: Scan Tool (M.U.T.-III Sub Assembly)

• MB991824: Vehicle Communication Interface (V.C.I.)

• MB991827: M.U.T.-III USB Cable

• MB991910: M.U.T.-III Main Harness A (Vehicles with

CAN communication system)

STEP 1. Measure the voltage at the occupant
classification-ECU connector.
(1) Disconnect the D-34-2 occupant classification-ECU

connector.

(2) Measure the voltage between the D-34-2 harness side

connector terminal No. 21 and the body ground.

• The voltage should measure 12 volts (battery positive

voltage).

Q: Is the measured voltage approximately 12 volts (battery

positive voltage)?
YES :
Go to Step 10.
NO : Go to Step 2.

STEP 2. Power supply fuse No.17 check.
Q: Is the fuse in good condition?

YES : Go to Step 4.
NO : Go to Step 3.

STEP 3. Wiring harness check between the C-315
ETACS-ECU connector terminal No.4 and the D-34-2
occupant classification-ECU connector terminal No. 21.

• Short circuit check for SRS-ECU power supply wire

Q: Is the check result normal?

YES : Replace the power supply fuse.
NO : Repair the wiring harness. And then replace the

power supply fuse.

AC709344AH

D-34-2 Harness side
connector (rear view)

Была ли эта страница вам полезна?
Да!Нет
9 посетителей считают эту страницу полезной.
Большое спасибо!
Ваше мнение очень важно для нас.

Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.

Текст

Политика конфиденциальности