Mitsubishi Outlander GS45X. Manual — part 1370
REAR WIPER AND WASHER
TSB Revision
EXTERIOR
51-103
INSTALLATION SERVICE POINTS
.
>>A<< REAR WIPER BLADE INSTALLATION
CAUTION
Use a curved backing like that shown for the backing of a
wiper blade to ensure sustained wiper wiping perfor-
mance.
.
>>B<< REAR WIPER ARM AND BLADE
ASSEMBLY INSTALLATION
Install the rear wiper arm and blade assembly so that it stops at
the specified position.
(A): 0 to 20 mm (0 to 0.79 in) from the ceramic line
INSPECTION
M1511019102905
REAR WIPER MOTOR CHECK
Inspect the rear wiper motor by disconnecting the harness con-
nector with the motor attached to the vehicle.
.
REAR WIPER MOTOR OPERATION CHECK
Connect the battery to the rear wiper motor to inspect the motor
operation as shown in the illustration.
.
REAR WIPER MOTOR STOP POSITION CHECK
1. Connect the battery to the rear wiper motor as shown in the
illustration.
2. Disconnect the battery in the middle of the motor rotation
and check to see that the motor stops.
3. Reconnect the battery.
4. Check to see that the rear wiper motor runs and then stops
at the automatic stop position.
AC101090
AE
A
A
Wiper blade
Backing
Backing
Section A – A
Wiper
blade
Backing
AC702736AC
A
Ceramic line
Rear wiper arm and
blade assembly
AC103246
AC506678
AB
Operation check
Stop position check
REAR WIPER AND WASHER
TSB Revision
EXTERIOR
51-104
REAR WASHER MOTOR INSPECTION
.
1. The rear washer motor must be checked with the washer
tank installed and the washer fluid filled.
2. Connect the battery to the washer motor connector as
shown. Check that the washer motor delivers washer
strongly to the rear washer hose side.
CHECKING THE REAR WASHER NOZZLE
INJECTION DIRECTION
NOTE: Use special tool Adjustment tool, washer nozzle
(MB992326) to adjust the splashing points of the nozzle.
.
ADJUSTMENT OF THE JET TYPE WASHER
NOZZLE INJECTION POSITION
CAUTION
Adjust the splashing position within the specified adjust-
ment range, otherwise the windshield cannot be washed
properly.
1. Use special tool Adjustment tool, washer nozzle
(MB992326) to adjust the splashing points of the nozzle.
2. Insert the jet type washer nozzle adjusting side of the
special tool Adjustment tool, washer nozzle (MB992326)
into the injection part of the washer nozzle as shown in
figure (A).
3. Move the special tool Adjustment tool, washer nozzle
(MB992326) up and down to adjust the angle of the washer
nozzle as shown in figure (B).
AC506693AB
Rear washer
hose
AC900637
AD
MB992326
Mist type
washer nozzle adjusting side
Jet type washer nozzle
adjusting side
AC900956
AD
MB992326
(A)
Jet type
washer nozzle
adjusting side
Jet type
washer nozzle
AC900958
AC
MB992326
Jet type
washer nozzle
adjusting side
Jet type
washer nozzle
REAR WIPER AND WASHER
TSB Revision
EXTERIOR
51-105
CHECKING THE REAR WIPER AND WASHER
SWITCH
The rear wiper and washer switch can be checked for proper
operation by confirming ETACS diagnosis trouble code. (Refer
to GROUP 54A - ETACS
AC900957
AC
MB992326
(B)
Jet type
washer nozzle
adjusting side
Jet type
washer nozzle
AC702737
3(0.12)
AB
Unit: mm (in)
40(1.57)
25(0.98)
180(7.09)
25(0.98)
Liftgate spoiler
Vehicle center line
Rear washer nozzle
Ceramic
line terminal
MARK
TSB Revision
EXTERIOR
51-106
MARK
REMOVAL AND INSTALLATION
M1511011803798
AC704254
AC901270
1
10
N
8
N
3
N
4
N
5
N
2
AC
6
N
7
N
9
N
1.
Front three-diamond mark (Refer to
)
>>A<<
2.
Rear three-diamond mark (Refer to
)
>>A<<
3.
MITSUBISHI mark <Vehicles for
USA and Canada>
>>A<<
4.
OUTLANDER mark <Vehicles for
Puerto Rico and Mexico>
>>A<<
5.
OUTLANDER mark <Vehicles for
USA and Canada>
>>A<<
6.
V6 mark <Vehicles for USA and
Canada>
>>A<<
7.
V6 mark <Vehicles for Puerto Rico
and Mexico>
>>A<<
8.
V6 mark <3000>
>>A<<
9.
4WD mark<4WD>
>>A<<
10. ULEV (ULTRA LOW EMISSIONS
VEHICLE) mark (LH) <Vehicles for
California (3000)>
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст