Mitsubishi Outlander GS45X. Manual — part 979
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <3.0L ENGINE>
13B-849
Target idle
speed
3
Target idle
speed
Engine: idling
Engine coolant
temperature is
−20°C (−4°F)
1,300
− 1,500
r/min
−
−
Engine coolant
temperature is
0
°C (32°F)
1,200
− 1,400
r/min
Engine coolant
temperature is
20
°C (68°F)
1,200
− 1,400
r/min
Engine coolant
temperature is
40
°C (104°F)
1,060
− 1,260
r/min
Engine coolant
temperature is
80
°C (176°F)
550
− 750
r/min
Throttle
actuator
58
Throttle
actuator
control motor
Engine: warming up
• The target opening degree
of the throttle valve is
shown.
• "0 %" means " fully closed
throttle valve" and "100 %"
means "fully opened
throttle valve".
0
− 100 %
(Display
range)
−
−
M.U.T.-III
SCAN
TOOL
DISPLAY
ITEM
NO.
INSPECTION
ITEM
INSPECTION REQUIREMENT
NORMAL
CONDITION
INSPECTION
PROCEDURE
NO.
REFERENCE
PAGE
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <3.0L ENGINE>
13B-850
TP sensor
(main)
13
Throttle
position
sensor (main)
• Remove the
intake air
hose at the
throttle body
• Disconnect
the throttle
position
sensor
connector,
and then
connect
terminals
No. 3, No. 4,
No. 5 and
No. 6 with
the use of
the special
tool:
MB991658.
• Ignition
switch: "ON"
Fully close the
throttle valve
with your finger
300
− 700
mV
Code No.
P0122,
P0123
Fully open the
throttle valve
with your finger
4,000 mV or
more
Engine:
warming up,
idling
No load
500
− 660
mV
A/C switch:
"OFF"
→ "ON"
Voltage rises
Shift lever: "N"
→ "D"
TP sensor
(main)
AB
Throttle
position
sensor (main)
• Remove the
intake air
hose at the
throttle body
• Disconnect
the throttle
position
sensor
connector,
and then
connect
terminals
numbers
No. 3, No. 4,
No. 5 and
No. 6 with
the use of
the special
tool:
MB991658.
• Ignition
switch: "ON"
Fully close the
throttle valve
with your finger
6
− 14 %
Code No.
P0122,
P0123
Fully open the
throttle valve
with your finger
80 % or more
M.U.T.-III
SCAN
TOOL
DISPLAY
ITEM
NO.
INSPECTION
ITEM
INSPECTION REQUIREMENT
NORMAL
CONDITION
INSPECTION
PROCEDURE
NO.
REFERENCE
PAGE
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <3.0L ENGINE>
13B-851
TP sensor
(main)
learned
value
14
Throttle
position
sensor (main)
mid opening
learning
value
This item shows the throttle valve opening
learning value when the vehicle enters into the
limp home mode.
−
−
TP sensor
(sub)
15
Throttle
position
sensor (sub)
• Remove the
intake air
hose at the
throttle body
• Disconnect
the throttle
position
sensor
connector,
and then
connect
terminals
No. 3, No. 4,
No. 5 and
No. 6 with
the use of
the special
tool:
MB991658.
• Ignition
switch: "ON"
Fully close the
throttle valve
with your finger
4,000 mV or
more
Code No.
P0222,
P0223
Fully open the
throttle valve
with your finger
1,000 mV or
less
M.U.T.-III
SCAN
TOOL
DISPLAY
ITEM
NO.
INSPECTION
ITEM
INSPECTION REQUIREMENT
NORMAL
CONDITION
INSPECTION
PROCEDURE
NO.
REFERENCE
PAGE
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <3.0L ENGINE>
13B-852
TP sensor
(sub)
BD
Throttle
position
sensor (sub)
• Remove the
intake air
hose at the
throttle body
• Disconnect
the throttle
position
sensor
connector,
and then
connect
terminals
numbers
No. 3, No. 4,
No. 5 and
No. 6 with
the use of
the special
tool:
MB991658.
• Ignition
switch: "ON"
Fully close the
throttle valve
with your finger
6
− 14 %
Code No.
P0222,
P0223
Fully open the
throttle valve
with your finger
80 % or more
Vehicle
speed
4
Vehicle
speed
Drive at 40 km/h (25 mph).
Approximatel
y 40 km/h (25
mph)
−
−
M.U.T.-III
SCAN
TOOL
DISPLAY
ITEM
NO.
INSPECTION
ITEM
INSPECTION REQUIREMENT
NORMAL
CONDITION
INSPECTION
PROCEDURE
NO.
REFERENCE
PAGE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст