Mitsubishi Outlander GS45X. Manual — part 806
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <3.0L ENGINE>
13B-157
CIRCUIT OPERATION
• A 5-volt voltage is supplied to the manifold abso-
lute pressure sensor power terminal (terminal No.
3) from the ECM (terminal No. 44). The ground
terminal (terminal No. 2) is grounded with ECM
(terminal No. 46).
• A voltage that is proportional to the intake mani-
fold pressure is sent to the ECM (terminal No. 45)
from the manifold absolute pressure sensor out-
put terminal (terminal No. 1).
.
TECHNICAL DESCRIPTION
• The manifold absolute pressure sensor outputs a
voltage which corresponds to the intake manifold
pressure.
• The ECM checks whether this voltage is within a
specified range.
.
DESCRIPTIONS OF MONITOR METHODS
Manifold absolute pressure sensor output voltage is
out of specified range.
.
MONITOR EXECUTION
Continuous
.
MONITOR EXECUTION CONDITIONS
(Other monitor and Sensor)
Other Monitor (There is no temporary DTC stored
in memory for the item monitored below)
• Not applicable
Sensor (The sensor below is determined to be
normal)
• Engine coolant temperature sensor
• Throttle position sensor
• Mass airflow sensor
• Intake air temperature sensor
• Barometric pressure sensor
.
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <3.0L ENGINE>
13B-158
DTC SET CONDITIONS
Logic Flow Chart
.
Check Conditions
• 8 minutes or more have passed since the engine
starting sequence was completed, when the
engine coolant temperature at engine start is 0
°C
(32
°F) or lower.
• Volumetric efficiency is higher than 20 percent.
Judgement Criterion
• Manifold absolute pressure is 5 kPa (1.5 in.Hg) or
lower for 2 seconds.
.
OBD-II DRIVE CYCLE PATTERN
Refer to Diagnostic Function
− OBD-II Drive Cycle −
Pattern 7
.
.
TROUBLESHOOTING HINTS (The most
likely causes for this code to be set are: )
• Manifold absolute pressure sensor failed.
• Connector damage
• Harness damage
• ECM failed.
DIAGNOSIS
Required Special Tools:
• MB991958: Scan Tool (M.U.T.-III Sub Assembly)
• MB991824: V.C.I.
• MB991827: USB Cable
• MB991910: Main Harness A
Yes
Yes
Yes
Yes
No
No
No
No
Monitoring
conditions
Pressure
< 5kPa (1.5in.Hg)
Pressure
> 117kPa (34.6in.Hg)
Continuous
failure for 2secs
Malfunction
End
Good
Start
AK604313
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <3.0L ENGINE>
13B-159
STEP 1. Using scan tool MB991958, check data list item 8:
Manifold Absolute Pressure Sensor.
CAUTION
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before con-
necting or disconnecting scan tool MB991958.
(1) Connect scan tool MB991958 to the data link connector.
(2) Turn the ignition switch to the "ON" position.
(3) Set scan tool MB991958 to the data reading mode for item
8, Manifold Absolute Pressure Sensor.
• When altitude is 0 m (0 foot), 101 kPa (29.8 in.Hg).
• When altitude is 600 m (1,969 feet), 95 kPa (28.1 in.Hg).
• When altitude is 1,200 m (3,937 feet), 88 kPa (26.0
in.Hg).
• When altitude is 1,800 m (5,906 feet), 81 kPa (23.9
in.Hg).
(4) Start the engine.
• When the engine is idling, 16 − 36 kPa (4.7 − 10.6
in.Hg).
• When the engine is suddenly revved, manifold absolute
pressure varies.
(5) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the sensor operating properly?
YES : It can be assumed that this malfunction is intermittent.
Refer to GROUP 00, How to Use
Troubleshooting/Inspection Service Points
− How to
Cope with Intermittent Malfunctions
P.00-15
.
NO : Go to Step 2.
STEP 2. Check harness connector B-105 at the manifold
absolute pressure sensor and harness connector B-10 at
the ECM for damage.
Q: Is the harness connector in good condition?
YES : Go to Step 3.
NO : Repair it. Refer to GROUP 00E, Harness Connector
Inspection
P.00E-2
. Then go to Step 7.
STEP 3. Measure the sensor supply voltage at manifold
absolute pressure sensor connector B-105.
(1) Disconnect the connector B-105.
(2) Turn the ignition switch to the "ON" position.
(3) Measure the voltage between terminal No. 1 and ground.
• Voltage should be between 4.9 and 5.1 volts.
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the measured voltage between 4.9 and 5.1 volts?
YES : Go to Step 5.
NO : Go to Step 4.
AK700568AB
MB991824
MB991827
MB991910
Data link
connector
AK900589
3 2 1
AB
B-105 harness
connector:
component side
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <3.0L ENGINE>
13B-160
STEP 4. Check for open circuit and short circuit to ground
between manifold absolute pressure sensor connector
B-105 and ECM connector B-10.
(1) Disconnect the manifold absolute pressure sensor
connector B-105 and the ECM connector B-10
(2) Measure the resistance between the manifold absolute
pressure sensor connector B-105 (terminal No. 1) and the
ECM connector B-10 (terminal No. 44).
• Should be less than 2 ohms.
(3) Check for the continuity between the manifold absolute
pressure sensor B-105 (terminal No. 1) and ground.
• Not continuity.
Q: Is the harness wire in good condition?
YES : Replace the ECM. When the ECM is replaced,
register the ID code. Refer to GROUP 42B, Diagnosis
− ID Codes Registration Judgment Table <Vehicles
with KOS>
P.42B-15
or GROUP 42C, Diagnosis
− ID
Codes Registration Judgment Table <Vehicles with
WCM>
P.42C-10
. Then go to step 7.
NO : Repair it. Then go to Step 7.
AK900590
16 15 14 13 12 11 10 9 8 7 6 5 4 3
2
1
32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17
48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33
64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49
3 2 1
AB
B-105 harness
connector:
component side
B-10 harness
connector:
component side
AK900591
3 2 1
AB
B-105 harness
connector:
component side
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст