Mitsubishi Outlander GS45X. Manual — part 1649
TRANSAXLE CONTROL
TSB Revision
CVT
23A-153
TRANSAXLE CONTROL
REMOVAL AND INSTALLATION
M1231203200720
CAUTION
Before removing the clock spring connector, refer to GROUP 52B
− SRS Air Bag Service Precautions
and Air Bag Module and Clock Spring.
Pre-removal operation
• Front floor console assembly removal (Refer to GROUP
52A
− Floor Console Assembly
Post-installation operation
• Front floor console assembly installation (Refer to
GROUP 52A
− Floor Console Assembly
.)
• Key interlock mechanism check (Refer to
• Shift lock mechanism check (Refer to
.)
• Transmission range switch and control cable adjustment
(Refer to
.)
AC505752AG
4
5
2
7
1
6
3
9.5 ± 3.5 N·m
84 ± 30 in-lb
7.0 ± 3.0 N·m
62 ± 26 in-lb
9.5 ± 3.5 N·m
84 ± 30 in-lb
4.3 ± 0.7 N·m
38 ± 6 in-lb
Selector lever assembly and
transaxle control cable assembly
removal steps
• Move the selector lever to the N
position.
1. Selector lever knob
2. Shift indicator panel
>>
A
<< 3. Key interlock cable connection
(selector lever side)
4. transaxle control cable connection
(selector lever side)
• Connectors and harnesses connections
5. Selector lever assembly
• Battery and battery tray (Refer to
GROUP 54A - Battery
• Air Cleaner (Refer to GROUP 15 − Air
Cleaner
.)
6. transaxle control cable connection
(transaxle side)
• Heater unit assembly (Refer to GROUP
55A - heater unit and front deck
crossmember assembly removal and
installation
7. transaxle control cable
Selector lever assembly and
transaxle control cable assembly
removal steps (Continued)
TRANSAXLE CONTROL
TSB Revision
CVT
23A-154
INSTALLATION SERVICE POINT
.
>>A<< KEY INTERLOCK CABLE INSTALLATION
CAUTION
Leave the ignition switch in the LOCK (OFF) position until
the key interlock cable installation is completed.
1. Move the selector lever to the P position and turn the ignition
switch to the LOCK (OFF) position.
2. Install the tip of the key interlock cable to the lock cam of the
selector lever assembly, taking care not to twist the inner
cable.
3. Install the adjuster case with its lock guide pulled up
(unlocked).
4. Securely push down the lock guide to lock it.
NOTE: The lock position of the key interlock cable is automati-
cally adjusted by a spring.
SHIFT SWITCH ASSEMBLY CONTINUITY CHECK
M1231030100552
AC709743
Inner cable
Adjuster case
Key inter lock cable
Lock guide
Lock cam
A
AB
View A
Spring
Lock
Adjuster case
Lock guide
Unlock
Shift
switch
assembly
Transmissi
on range
Terminal
number
Continuity
Select
switch
Sport mode 6
− 8
Continuity
Other than
above
6
− 8
No
continuity
Shift switch
(UP)
Upshift and
hold
6
− 10
Continuity
Other than
above
6
− 10
No
continuity
Shift switch
(DOWN)
Downshift
and hold
6
− 9
Continuity
Other than
above
6
− 9
No
continuity
AC507005
9
3
2
1
5 6 7 8
4
10
AB
Selector lever assembly
CVT KEY INTERLOCK AND SHIFT LOCK MECHANISMS
TSB Revision
CVT
23A-155
CVT KEY INTERLOCK AND SHIFT LOCK MECHANISMS
REMOVAL AND INSTALLATION
M1231203400315
REMOVAL SERVICE POINT
.
<<A>> KEY INTERLOCK CABLE (STEERING
SIDE) REMOVAL
Turn the ignition switch to the ACC position and then pull the
key interlock cable out from the ignition key cylinder.
Pre-removal operation
• Steering column lower cover and side lower panel assem-
bly removal (Refer to GROUP 52A
− Instrument Panel
Assembly
.)
• Front floor console assembly removal (Refer to GROUP
52A
− Floor Console Assembly
Post-installation operation
• Steering column lower cover and side lower panel assem-
bly installation (Refer to GROUP 52A
− Instrument Panel
Assembly
.)
• Front floor console assembly installation (Refer to
GROUP 52A
− Floor Console Assembly
.)
• Key interlock mechanism check (Refer to
• Shift lock mechanism check (Refer to
.)
• Selector lever operation check (Refer to
.)
AC607789AB
1
2
3
Removal steps
>>
B
<< 1.
Key interlock cable connection
(selector lever side)
<<
A
>> >>
A
<< 2.
Key interlock cable connection
(steering side)
3.
Key interlock cable
Removal steps (Continued)
CVT KEY INTERLOCK AND SHIFT LOCK MECHANISMS
TSB Revision
CVT
23A-156
INSTALLATION SERVICE POINTS
.
>>A<< KEY INTERLOCK CABLE (STEERING
LOCK CYLINDER SIDE) INSTALLATION
Turn the ignition switch to the ACC position and then install the
key interlock cable to the ignition key cylinder.
.
>>B<< KEY INTERLOCK CABLE INSTALLATION
CAUTION
Leave the ignition switch in the LOCK (OFF) position until
the key interlock cable installation is completed.
1. Move the selector lever to the P position and turn the ignition
switch to the LOCK (OFF) position.
2. Install the tip of the key interlock cable to the lock cam of the
selector lever assembly, taking care not to twist the inner
cable.
3. Install the adjuster case with its lock guide pulled up
(unlocked).
4. Securely push down the lock guide to lock it.
NOTE: The lock position of the key interlock cable is automati-
cally adjusted by a spring.
AC709743
Inner cable
Adjuster case
Key inter lock cable
Lock guide
Lock cam
A
AB
View A
Spring
Lock
Adjuster case
Lock guide
Unlock
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст