Mitsubishi Lancer Evolution 8. Manual — part 182
INTAKE & EXHAUST –SECONDARY AIR CONTROL SYSTEM INLET MANIFOLD
FITTING
A
Gasket fitting
Fit so that the gasket protruding part points in the direction indicated in the
diagram.
Inlet manifold
Fitting and removal
Pre-removal and post-fitting operations
• Measures to prevent any leakage of fuel <pre-removal
only>
• Removal and fitting of cover
(ref. Chapter 51 – Front Bumper)
• Draining and filling of coolant
• Removal and fitting of air duct
• Removal and fitting of strut tower bar
• Removal and fitting of throttle body
• Removal and fitting of air control valve bracket (P.15-6)
• Removal and fitting of cross member bar
• Removal and fitting of front exhaust pipe
Protruding
part
15-7
INTAKE & EXHAUST – SECONDARY AIR CONTROL SYSTEM
15-8
Removal procedure
1. Centre cover
2. Ignition coil connector connection
3. O2 sensor connector connection
4. Crank angle sensor connector connection
5. Injector connector connection
6. Fuel pressure solenoid valve connector
connection
7. Purge solenoid valve connector
connection
8. Knock sensor connector connection
9. Vacuum hose connection
10. Vacuum hose
11. Fuel return hose connection
12. Fuel high pressure hose connection
13. O-ring
14. Delivery pipe, injector & fuel pressure
regulator ASSY
15. Insulator
16. Insulator
17. Oil level gauge & guide ASSY
18. O-ring
19. Brake booster vacuum hose connection
20. Purge hose connection
A
A
INTAKE & EXHAUST – INLET MANIFOLD
Removal procedure
21. Knock sensor connector connection
22. Purge control solenoid valve ASSY
23. Vacuum hose
24. Fuel pressure solenoid valve ASSY
25. PCV hose
• Alternator
26. ACV solenoid valve connector connection
27. Vacuum tank, ACV solenoid valve, vacuum hose & pipe
ASSY
28. Inlet manifold stay
29. Cover
30. Gasket
31. Earth cable connection
32. Crank angle sensor connector connection
33. Alternator brace stay
34. Inlet manifold
35. Inlet manifold gasket
REMOVAL
A
Delivery pipe, injector and fuel pressure regulator ASSY removal
Remove the delivery pipe with the injector and fuel pressure regulator
attached.
CAUTION
When removing the delivery pipe, be careful not to drop the
injector.
FITTING
A
Fuel high pressure hose connection
1. Apply a small quantity of new engine oil to the O-ring, then insert the
O-ring into the delivery pipe without damaging it.
2. Check that the high pressure hose turns smoothly. When it does not
turn smoothly, it is possible that the O-ring is being pinched, in
which case remove the high pressure hose and, after checking to
see if the O-ring is damaged, re-insert into the delivery pipe.
3. Tighten mounting bolt to specified torque.
Specified torque: 5.0 ± 1.0 N·m
15-9
ENGINE ELECTRICAL – STARTING SYSTEM
16-1
SECTION 16
CONTENTS
Starting devices
General
The following servicing information has been issued in conjunction with changes to the 4G63-MPI-T/C engine starter ASSY on
the new Lancer Evolution VIII.
Other servicing information remains the same.
Starter
Removal and fitting
Pre-removal and post-fitting operations
• Removal and fitting or cover (ref. Chapter 51 – Front Bumper)
• Removal and fitting of cross member bar
• Removal and fitting of front exhaust pipe
Removal procedure
1. Starter cover
2. Starter connector and terminal
3. Starter ASSY
Starting devices . . . . . . . . . . .1
General . . . . . . . . . . . . . ...1
Starter . . . . . . . . . . . . . . .1
Ignition devices . . . . . . . . . . .2
General. . . . . . . . . . . . . . 2
Crank angle sensor . . . . . . . . ..2
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст