Mitsubishi Lancer Evolution IX. Manual — part 375
DOOR SASH TAPE
EXTERIOR
51-13
REMOVAL SERVICE POINT
<<A>> DOOR SASH TAPES REMOVAL
CAUTION
Pay attention to keep from getting burned by hot
door panel or tapes.
1. Use a hair drier to warm the tape.
2. Peel the tip of the tape with your finger, and then
peel off the tape parallel to the application
surface.
INSTALLATION SERVICE POINT
>>A<< DOOR SASH TAPES INSTALLA-
TION
CAUTION
• The ambient temperature should be 20 to
30
°C. Ensure that the working area is clean.
Ideally, the tape application should be done at
ambient temperature of 25
°C.
• If ambient temperature is less than 15°C, heat
the tape and application surface to a tempera-
ture of 20 to 30
°C. If ambient temperature is
35
°C or higher, cool down them. The adhesive
property of the tape is deteriorated at low
temperature, so the tape may come adrift eas-
ily. Meanwhile, it gets softened at hot temper-
ature.
• When beginning to apply the tape, pay partic-
ular attention. If the end of the tape cannot be
applied to the specified position with an accu-
racy of less than 1 mm, it may cause the poor
appearance or adhesion.
•
AC303428
40 to 50˚
30 to 45˚
10 to 20 mm
10 to 20 mm
AB
MB990528
MB990528
Door sash tape
Door sash tape
Backing paper
Backing paper
<Pushing direction>
<Pulling direction>
3 to 7 cm/sec.
3 to 7 cm/sec.
Use the special tool stripe tape spatula
(MB990528) to apply the tape with a steady
pace and pressure. If you do not apply the
tape with a steady pace or pressure, or abort
the application, a shallow groove (lateral
groove called as "Shock line") may be
present on the tape surface. Meanwhile, if you
apply it too quickly, air bubbles may be
formed under the tape.
1. Wrap a soft cloth (synthetic fibre) around the tip of
the special tool.
2. Use isopropyl alcohol to degrease the tape
application surface.
3. Wipe away dirt from the tape.
AC403580AC
3.5 mm
3.5 mm
5.0
mm
7.0
mm
3.5 mm
3.5 mm
3.5 mm
Tape overlap:
3.0 mm
Tape overlap:
3.0 mm
3.5 mm
RH only
RH only
RH only
Backing paper
cut-line
Tape perforate-
line
Tape perforate-
line
Backing paper
cut-line
Backing paper
cut-line
: Tape locating points
: T-stud for door opening weatherstrip attaching locations (5 pieces in all).
Tape perforate-
line
Front door sash
tape upper
Rear door sash
tape front
Rear door sash
tape upper
Front door sash
tape rear
DOOR SASH TAPE
EXTERIOR
51-14
4. Apply the door sash tapes according to the
procedures shown below.
(1) Align a tape with specified application position.
If necessary, use a magnet to secure it.
NOTE:
.
•
Align the front door sash tape upper at the
rear end.
•
Align the rear door sash tape upper at the
front end.
•
Align the front door sash tape rear/rear
door sash tape front at the upper end.
DOOR SASH TAPE
EXTERIOR
51-15
(2) As for the front/rear door sash tape upper, peel
off the backing paper under the tape by the
backing paper cut-line and apply the tape
temporarily.
AC303110AB
Backing paper
Door sash tape
(3) Peel off the backing paper and cut it as
necessary.
AC402197
AD
MB990528
Backing paper
Door sash
tape
(4) While peeling off the remaining backing paper,
press the tape by a special tool (MB990528).
NOTE:
.
•
Apply the front door sash tape upper from
rear to front.
•
Apply the rear door sash tape upper from
front to rear.
•
Apply the front door sash tape rear/rear
door sash tape front from top to bottom.
(5) As for the front door sash tape rear/rear door
sash tape front, peel off the application tape in
the direction of 180
° from bottom to top.
(6) Remove unnecessary part of the tape at tape
perforate-line.
AC303415
AB
MB990528
120˚
60˚
Hemming part
(7) Press the folded area of the tape at 3 steps
securely(60
°, 120° and holding), rolling in
toward the vehicle inside direction.
AC303443AE
A section
Tape pasting onto corner
(viewed from inside)
(8) As for the front door sash tape rear/rear door
sash tape front, roll in the A section of the tape
upper corner toward the vehicle inside with
your palm securely.
REAR SPOILER
EXTERIOR
51-16
REAR SPOILER
ADHESIVE
M1511000500512
Item
Specification
Rear spoiler assembly <Type A>
Double-sided tape: Generic products
3 mm thickness
Rear spoiler assembly <Type B>
Double-sided tape: Generic products
1.6 mm thickness
REMOVAL AND INSTALLATION
M1511006100211
<TYPE A>
AC310062
1
2
3
4
AC
3
4
1
3
3
Double-sided tape: Generic products, 3 mm thickness
Adhesive tape affixed location
Removal steps
•
Trunk lid bumper (Refer to GROUP
42, Trunk Lid
).
1. Cap
<<A>>
>>
A
<< 2. Rear spoiler assembly
3. Gasket
4. Rear spoiler
•
High-mounted stop lamp (Refer to
GROUP 54A, High-mounted Stop
Lamp
).
Removal steps (Continued)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст