Mitsubishi Lancer Evolution IX. Manual — part 376
REAR SPOILER
EXTERIOR
51-17
<Type B>
AC504553
Double-sided tape: Generic products, 1.6 mm thickness
Adhesive tape affixed location
AB
5.2 ± 0.2 N·m
5.2 ± 0.2 N·m
5.2 ± 0.2 N·m
5.2 ± 0.2 N·m
2
1
1
Removal steps
•
Trunk lid bumper (Refer to GROUP
42, Trunk Lid
).
1. Cap
<<
A
>> >>
A
<< 2. Rear spoiler assembly
REMOVAL SERVICE POINT
<<A>> REAR SPOILER ASSEMBLY
REMOVAL
Remove by the same procedure as described in
SIDE AIR DAM REMOVAL (Refer to
).
INSTALLATION SERVICE POINT
>>A<< REAR SPOILER ASSEMBLY
INSTALLATION
Install by the same procedure as described in SIDE
AIR DAM INSTALLATION (Refer to
WINDSHIELD WIPER AND WASHER
EXTERIOR
51-18
WINDSHIELD WIPER AND WASHER
SERVICE SPECIFICATION
M1511000300422
Item
Standard value
Stop position of the windshield wiper arm/blade assembly (Distance between the
edge of the wiper blade and the end of the deck garnish) mm
69
± 5
SPECIAL TOOLS
M1511000601783
Tool
Number
Name
Use
B991502
MB991502
M.U.T.-II sub
assembly
Check the windshield intermittent
wiper interval
MB991910
MB991826
MB991955
MB991911
MB991824
MB991827
MB991825
A
B
C
D
E
F
DO NOT USE
MB991955
A: MB991824
B: MB991827
C: MB991910
D: MB991911
E: MB991825
F: MB991826
M.U.T.-III
sub-assembly
A: Vehicle
Communication
Interface (V. C. I.)
B: M.U.T.-III USB
cable
C: M.U.T.-III main
harness A
(Vehicles with CAN
communication
system)
D: M.U.T.-III main
harness B
(Vehicles without
CAN
communication
system)
E: M.U.T.-III
measurement
adapter
F: M.U.T.-III trigger
harness
Check the windshield intermittent
wiper interval
CAUTION
M.U.T.-III main harness B
(MB991911) should be used.
M.U.T.-III main harness A
should not be used for this
vehicle.
MB991529
WINDSHIELD WIPER AND WASHER
EXTERIOR
51-19
TROUBLESHOOTING
M1511000700323
The windshield wiper and washer are controlled by
the Smart Wiring System (SWS). For troubleshoot-
ing, refer to GROUP 54B, Troubleshooting
or GROUP 54C, Troubleshooting
NOTE: Even when the ETACS-ECU has failed, the
windshield wiper can work at low speed as fail-safe
mode. (Normally, the windshield wiper operates
when the ignition switch is at the "ACC" position. But,
if it enters the fail-safe mode, the wiper can operate
only when the ignition switch is at the "ON" position.)
ON-VEHICLE SERVICE
WINDSHIELD INTERMITTENT WIPER
INSPECTION
M1511021900054
1. If the windshield intermittent wiper interval
adjusting knob is operated, the wiper interval
should change.
2. Holding the windshield intermittent wiper interval
adjusting knob, input the simulated vehicle speed
with M.U.T.-II / III and check that the wiper interval
changes as the vehicle speed changes.
3. If not, carry out the troubleshooting (Refer to
GROUP 54B, Troubleshooting
or
GROUP 54C, Troubleshooting
).
MB991529
Diagnosis code check
harness
Input signal check by using a
voltmeter
MB991223
a
d
c
b
DO NOT USE
BA
MB991223
a. MB991219
b. MB991220
c. MB991221
d. MB991222
Harness set
a. Check harness
b. LED harness
c. LED harness
adapter
d. Probe
Continuity check and voltage
measurement at harness wire or
connector
a. For checking connector pin
contact pressure
b. For checking power supply
circuit
c. For checking power supply
circuit
d. For connecting a locally
sourced tester
MB992006
MB992006
Extra fine probe
Continuity check and voltage
measurement at harness wire or
connector
Tool
Number
Name
Use
WINDSHIELD WIPER AND WASHER
EXTERIOR
51-20
WINDSHIELD WIPER
REMOVAL AND INSTALLATION
M1511007900209
AC211876
Note
:Indicates the clip (A) locations. :Indicates the clip (B) locations.
Section B – B
Section A – A
View A
6, 7
3, 4
Clip (A)
Clip (B)
2
1
2
4
4
1
27 ± 3 N·m
A
A
A
AF
5
6
6
7
7
8
9
7.4 ± 1.4 N·m
8.9 ± 1.9 N·m
B
B
3
Wiper blade assembly removal steps
>>
B
<< 1. Wiper blade assembly
>>
A
<< 2. Wiper blade
Windshield wiper motor and link
assembly removal steps
3. Cover
4. Wiper arm
5. Hood weather strip
6. Front deck garnish (Passenger's side)
7. Front deck garnish (Driver's side)
<<
A
>>
8. Windshield wiper motor assembly
9. Link assembly
Windshield wiper motor and link
assembly removal steps (Continued)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст