Mitsubishi Lancer Evolution IX. Manual — part 662
ENGINE ROLL STOPPER, CENTREMEMBER
POWER PLANT MOUNT
32-7
ENGINE ROLL STOPPER, CENTREMEMBER
REMOVAL AND INSTALLATION
M1321002300362
<LH DRIVE VEHICLES>
CAUTION
*: Indicates parts which should be initially tightened, and then fully tightened after placing the vehicle
horizontally and loading the full weight of the engine on the vehicle body.
Pre-removal Operation
• Under Cover Removal (Refer to GROUP 51, Front
).
Post-installation Operation
• Under Cover Installation (Refer to GROUP 51, Front
).
AC210447
49 ± 10 N·m
AB
1
10
9
8
7
6
5
4
3
2
1
49 ± 10 N·m
49 ± 10 N·m
69 ± 10 N·m
69 ± 10 N·m
45 ± 5 N·m*
45 ± 5 N·m*
52 ± 7 N·m*
70 ± 10 N·m
52 ± 7 N·m*
70 ± 10 N·m
52 ± 7 N·m*
Front roll stopper bracket and
centremember removal steps
1.
Front axle crossmember bars
2.
Engine front roll stopper bracket
bolt
3.
Front suspension centremember
>>
A
<< 4.
Engine front roll stopper bracket
5.
Transmission case front roll
stopper bracket
Rear roll stopper rod removal
steps
6.
Engine rear roll stopper rod bolt
7.
Transmission case rear roll
stopper bracket
8.
Engine rear roll stopper rod bolt
9.
Engine rear roll stopper rod
bracket
10. Engine rear roll stopper rod
ENGINE ROLL STOPPER, CENTREMEMBER
POWER PLANT MOUNT
32-8
<RH DRIVE VEHICLES>
CAUTION
*: Indicates parts which should be initially tightened, and then fully tightened after placing the vehicle
horizontally and loading the full weight of the engine on the vehicle body.
Pre-removal Operation
• Under Cover Removal (Refer to GROUP 51, Front
).
Post-installation Operation
• Under Cover Installation (Refer to GROUP 51, Front
).
AC310765
1
7
6
5
4
3
1
49 ± 10 N·m
49 ± 10 N·m
69 ± 10 N·m
69 ± 10 N·m
45 ± 5 N·m*
45 ± 5 N·m*
70 ± 10 N·m
52 ± 7 N·m*
70 ± 10 N·m
AB
8
49 ± 10 N·m
52 ± 7 N·m*
2
Front roll stopper bracket and
centremember removal steps
1.
Front axle crossmember bars
2.
Engine front roll stopper bracket
bolt
3.
Front suspension centremember
>>
A
<< 4.
Engine front roll stopper bracket
5.
Transmission case front roll
stopper bracket
Rear roll stopper rod removal
steps
6.
Engine rear roll stopper bolt
7.
Transmission case rear roll
stopper bracket
8.
Engine rear roll stopper bracket
ENGINE ROLL STOPPER, CENTREMEMBER
POWER PLANT MOUNT
32-9
INSTALLATION SERVICE POINT
>>A<< ENGINE FRONT ROLL STOPPER
BRACKET INSTALLATION
AC210448
Hole
Front of vehicle
AB
Install the front roll stopper so that its hole points
towards the front side of the vehicle.
INSPECTION
M1321002400080
• Check the engine roll stopper insulators for
cracks, separation or deformation.
CROSSMEMBER
POWER PLANT MOUNT
32-10
CROSSMEMBER
REMOVAL AND INSTALLATION
M1321003200443
<LH drive vehicles>
CAUTION
• Before removing the steering wheel and air bag module assembly, always refer to GROUP 52B -
Service Precautions, Air bag Module and Clock Spring. Also, set the front wheels so that they are
facing straight forward, and remove the ignition key. If you fail to do this, the SRS clock spring will
be damaged, causing the SRS air bag to be inoperative and serious injury.
• *
1
: Indicates parts which should be initially tightened, and then fully tightened after placing the
vehicle horizontally and loading the full weight of the engine on the vehicle body.
• *
2
: Indicates parts which should be temporarily tightened, and then fully tightened with the vehicle
on the ground in the unladen condition.
• If the vehicle is equipped with the Brembo™ disc brake, during maintenance, take care not to con-
tact the parts or tools to the caliper because the paint of caliper will be scratched.
Pre-removal and Post-installation Operation
• Under Cover Removal (Refer to GROUP 51, Front
).
• Front Axle Crossmember Bar, Front Suspension Center-
member Removal (Refer to
• Front Exhaust Pipe Removal (Refer to GROUP 15,
Exhaust Pipe and Main Muffler
• Steering Wheel Air Bag Module Assembly Removal
(Refer to GROUP 37, Steering Wheel
• Power Steering Fluid Draining (Refer to GROUP 37,
On-vehicle Service
− Fluid Replacement
Pre-removal and Post-installation Operation
• Front Exhaust Pipe Installation (Refer to GROUP 15,
Exhaust Pipe and Main Muffler
• Front Axle Crossmember Bar, Front Suspension Center-
member Installation (Refer to
• Steering Wheel Air Bag Module Assembly Installation
(Refer to GROUP 37, Steering Wheel
• Power Steering Fluid Supplying (Refer to GROUP 37,
On-vehicle Service
− Fluid Replacement
• Power Steering Fluid Line Bleeding (Refer to GROUP 37,
On-vehicle Service
− Power Steering System Air Bleeding
• Press the dust cover with a finger to check whether the
dust cover cracked or damaged.
• Checking Steering Wheel Position with Wheels Straight
Ahead.
• Front Wheel Alignment Check and Adjustment (Refer to
GROUP 37, On-vehicle Service
− Steering Angle Check
).
• Under Cover Installation (Refer to GROUP 51, Front
).
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст