Mitsubishi Lancer Evolution IX. Manual — part 211
SYMPTOM PROCEDURES
SMART WIRING SYSTEM (SWS) USING SWS MONITOR
54C-103
Step 23. Check the wiring harness from E-17
power window sub switch (rear: RH) connector
terminal No.1 to body earth.
NOTE:
Prior to the wiring harness inspection, check interme-
diate connectors D-04, and repair if necessary.
• Check the earth wires for open circuit.
Q: Is the check result normal?
YES :
The trouble can be an intermittent
malfunction (Refer to GROUP 00, How to
Cope with Intermittent Malfunction
NO :
Repair the wiring harness.
Step 24. Voltage measurement at E-17 power
window sub switch (rear: RH) connector
(1) Disconnect the connector, and measure at the
wiring harness side.
(2) Turn the ignition switch to the ON position.
(3) Voltage between E-17 power window sub switch
(rear: RH) connector terminal 4 and body earth
OK: System voltage
Q: Is the check result normal?
YES :
Go to Step 27.
NO :
Go to Step 25.
AC310491
Connector: E-17
AC
Harness side
Rear door (RH)
AC310463
Connector: D-04 <LHD>
AB
AC310471
Connector: D-04 <RHD>
AC
AC310491
Connector: E-17
AC
Harness side
Rear door (RH)
AC310507
Connector E-17
(Harness side)
AE
SYMPTOM PROCEDURES
SMART WIRING SYSTEM (SWS) USING SWS MONITOR
54C-104
Step 25. Connector check: C-224 power window
relay connector
Q: Is the check result normal?
YES :
Go to Step 26.
NO :
Repair the connector.
Step 26. Check the wiring harness from E-17
power window sub switch (rear: RH) connector
terminal No.4 to C-224 power window connector
terminal No.4.
AC310448
AI
Connector: C-224 <LHD>
Junction block (front view)
Junction block side
AC310458
AG
Connector: C-224 <RHD>
Junction block (front view)
Junction block
side
AC310491
Connector: E-17
AC
Harness side
Rear door (RH)
AC310449
AD
Connectors: C-211, C-224 <LHD>
Junction block (front view)
Junction block side
C-211
C-224
C-224
Harness side
C-211
AC310459
AD
Connectors: C-211, C-224 <RHD>
Junction block (front view)
Junction block side
C-211
C-224
C-224
Harness side
C-211
SYMPTOM PROCEDURES
SMART WIRING SYSTEM (SWS) USING SWS MONITOR
54C-105
NOTE:
Prior to the wiring harness inspection, check interme-
diate connectors C-112 <LH drive vehicles>, C-113
<RH drive vehicles>, D-04 and junction block con-
nector C-211, and repair if necessary.
• Check the power supply line for open circuit.
Q: Is the check result normal?
YES :
The trouble can be an intermittent
malfunction (Refer to GROUP 00, How to
Cope with Intermittent Malfunction
NO :
Repair the wiring harness.
Step 27. Connector check: E-16 power window
regulator motor (rear: RH) connector
Q: Is the check result normal?
YES :
Go to Step 28.
NO :
Repair the connector.
Step 28. Check the wiring harness from E-16
power window regulator motor (rear: RH)
connector terminal Nos.1 and 4 to E-17 power
window sub switch (rear: RH) connector terminal
Nos.5 and 7.
• Check the input and output lines for open or short
circuit.
Q: Is the check result normal?
YES :
Go to Step 29.
NO :
Repair the wiring harness.
AC310452
Connector: C-112 <LHD>
AD
C-112 (GR)
AC310456
Connector: C-113 <RHD>
AN
AC310463
Connector: D-04 <LHD>
AB
AC310471
Connector: D-04 <RHD>
AC
AC310491
Connector: E-16
AD
Harness side
E-16 (GR)
Rear door (RH)
AC310492
Harness side
Connectors: E-16, E-17
E-16
E-17
Harness side
E-17
E-16 (GR)
AB
Rear door (RH)
SYMPTOM PROCEDURES
SMART WIRING SYSTEM (SWS) USING SWS MONITOR
54C-106
Step 29. Retest the system.
After the power window sub switch (rear: RH) is
replaced, check that the rear right door power win-
dow can be operated by the power window sub
switch (rear: RH).
(1) Replace the power window sub switch (rear: RH).
(2) Check that the rear right door power window can
be operated by the power window sub switch
(rear: RH).
Q: Is the check result normal?
YES :
The trouble can be an intermittent
malfunction (Refer to GROUP 00
− How to
Cope with Intermittent Malfunction
NO :
Replace the rear power window regulator
motor assembly (RH).
Step 30. Connector check: E-08 power window
sub switch (rear LH) connector
Q: Is the check result normal?
YES :
Go to Step 31.
NO :
Repair the connector.
Step 31. Resistance measurement at E-08 power
window sub switch (rear: LH) connector
(1) Disconnect the connector, and measure at the
wiring harness side.
(2) Resistance between E-08 power window sub
switch (rear: LH) connector terminal 1 and body
earth
OK: 2
Ω or less
Q: Is the check result normal?
YES :
Go to Step 33.
NO :
Go to Step 32.
AC310486
Connector: E-08
AD
Harness side
Rear door (LH)
AC310486
Connector: E-08
AD
Harness side
Rear door (LH)
AC303981
Connector E-08
(Harness side)
AB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст