Mitsubishi Lancer Evolution IX. Manual — part 212
SYMPTOM PROCEDURES
SMART WIRING SYSTEM (SWS) USING SWS MONITOR
54C-107
Step 32. Check the wiring harness from E-08
power window sub switch (rear: LH) connector
terminal No.1 to body earth.
NOTE:
Prior to the wiring harness inspection, check interme-
diate connectors D-15, and repair if necessary.
• Check the earth wires for open circuit.
Q: Is the check result normal?
YES :
The trouble can be an intermittent
malfunction (Refer to GROUP 00, How to
Cope with Intermittent Malfunction
NO :
Repair the wiring harness.
Step 33. Voltage measurement at E-08 power
window sub switch (rear: LH) connector
(1) Disconnect the connector, and measure at the
wiring harness side.
(2) Turn the ignition switch to the ON position.
(3) Voltage between E-08 power window sub switch
(rear: LH) connector terminal 4 and body earth
OK: System voltage
Q: Is the check result normal?
YES :
Go to Step 36.
NO :
Go to Step 34.
AC310486
Connector: E-08
AD
Harness side
Rear door (LH)
AC310465
AC
Connector: D-15 <LHD>
AC310473
AD
Connector: D-15 <RHD>
AC310486
Connector: E-08
AD
Harness side
Rear door (LH)
AC303982
Connector E-08
(Harness side)
AB
SYMPTOM PROCEDURES
SMART WIRING SYSTEM (SWS) USING SWS MONITOR
54C-108
Step 34. Connector check: C-224 power window
relay connector
Q: Is the check result normal?
YES :
Go to Step 35.
NO :
Repair the connector.
Step 35. Check the wiring harness from E-08
power window sub switch (rear: LH) connector
terminal No.4 to C-224 power window relay
connector terminal No.4.
AC310448
AI
Connector: C-224 <LHD>
Junction block (front view)
Junction block side
AC310458
AG
Connector: C-224 <RHD>
Junction block (front view)
Junction block
side
AC310486
Connector: E-08
AD
Harness side
Rear door (LH)
AC310449
AD
Connectors: C-211, C-224 <LHD>
Junction block (front view)
Junction block side
C-211
C-224
C-224
Harness side
C-211
AC310459
AD
Connectors: C-211, C-224 <RHD>
Junction block (front view)
Junction block side
C-211
C-224
C-224
Harness side
C-211
SYMPTOM PROCEDURES
SMART WIRING SYSTEM (SWS) USING SWS MONITOR
54C-109
NOTE:
Prior to the wiring harness inspection, check interme-
diate connectors C-127, D-15 and junction block
connector C-211, and repair if necessary.
• Check the power supply line for open circuit.
Q: Is the check result normal?
YES :
The trouble can be an intermittent
malfunction (Refer to GROUP 00, How to
Cope with Intermittent Malfunction
NO :
Repair the wiring harness.
Step 36. Connector check: E-09 power window
regulator motor (rear: LH) connector
Q: Is the check result normal?
YES :
Go to Step 37.
NO :
Repair the connector.
Step 37. Check the wiring harness from E-09
power window regulator motor (rear: LH)
connector terminal Nos.1 and 4 to E-08 power
window sub switch (rear: LH) connector terminal
Nos.5 and 7.
• Check the input and output lines for open or short
circuit.
Q: Is the check result normal?
YES :
Go to Step 38.
NO :
Repair the wiring harness.
AC310446
AO
Connector: C-127 <LHD>
AC310454
AI
Connector: C-127 <RHD>
AC310465
AC
Connector: D-15 <LHD>
AC310473
AD
Connector: D-15 <RHD>
AC310486
Connector: E-09
AB
Harness side
E-09 (GR)
Rear door (LH)
AC310487
Connectors: E-08, E-09
E-09
E-08
Harness side
Rear door (LH)
Harness side
E-08
E-09 (GR)
AB
SYMPTOM PROCEDURES
SMART WIRING SYSTEM (SWS) USING SWS MONITOR
54C-110
Step 38. Retest the system.
After the power window sub switch (rear: LH) is
replaced, check that the rear left door power window
can be operated by the power window sub switch
(rear: LH).
(1) Replace the power window sub switch (rear: LH).
(2) Check that the rear left door power window can
be operated by the power window sub switch
(rear: LH).
Q: Is the check result normal?
YES :
The trouble can be an intermittent
malfunction (Refer to GROUP 00
− How to
Cope with Intermittent Malfunction
NO :
Replace the rear power window regulator
motor assembly (LH).
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст