Mitsubishi Lancer. Manual — part 192
ON-VEHICLE SERVICE
POWER STEERING
37-16
WARNING
•
If the vehicle continues to be driven after
the collision absorbing mechanism has
operated, the steering column shaft may
be damaged while it is in use.
•
If there is a slack in the one-way capsule,
do not attempt to repair it but replace the
steering column shaft assembly.
Inspection Procedure
1. Remove the lower and upper column covers.
CAUTION
Do not release the tilt lever until the steering col-
umn has been installed to complete this inspec-
tion procedure.
2. Ensure that the tilt lever is in the lock position.
NOTE: If not, place the tilt lever in the lock posi-
tion.
AC304673
AC304673
Steering
column
assembly
AB
Steering
column
mounting
bolt
3. Loosen the two steering column mounting bolts
(upper) by two turns.
AC304672
AC304673
AC304673
AC304923
AB
One way capsule
4. Hold the one way capsule as shown, and then try
to lock them. If there is a slack in either of the
capsules, replace the steering column shaft
assembly.
NOTE: When installing a new steering column
shaft assembly, place the tilt lever in the lock posi-
tion, if it is not in place.
CAUTION
• Be careful that nothing is pinched between
the one-way capsules and the body.
• Do not release the tilt lever until the steering
column has been installed to complete this
inspection procedure.
5. If no problem is found during the inspection,
tighten the steering column mounting bolts to the
specified torque.
Tightening torque: 12
± 2 N⋅ m
STEERING WHEEL
POWER STEERING
37-17
STEERING WHEEL
REMOVAL AND INSTALLATION <INVITE>
M1372011400183
WARNING
•
Before removing the steering wheel and air bag module assembly, refer to GROUP 52B,
Service Precautions (
) and Air Bag Module and Clock Spring (
).
•
Post-installation Operation
• Checking Steering Wheel Position with Wheels Straight
Ahead
AC107402AB
50 ± 5 N·m
1
2
2
1
1
2
A
A
B
B
Tab
Tab
Section A - A
Section B - B
Removal steps
<<
A
>>
1. Cover
<<
B
>>
2. Steering wheel and air bag module
assembly
When removing and installing the steering wheel, do not let it bump against the air bag
module.
NOTE: For air bag module removal, refer to GROUP
52B, Air Bag Module and Clock Spring
.
REMOVAL SERVICE POINTS
<<A>> COVER REMOVAL
AC006294 AB
MB990784
Insert special tool ornament remover (MB990784) at
the indicated position to remove the cover.
NOTE: The special tool can be inserted through the
notch behind the area shown.
STEERING WHEEL
POWER STEERING
37-18
<<B>> STEERING WHEEL AND AIR BAG
MODULE ASSEMBLY REMOVAL
AC105823
AC304700
AC305145AB
A
Steering
wheel
Air bag module
connector
1. By sliding section A of the clock spring connector
shown in the illustration in the arrow direction,
disconnect the connector.
AC100442
Hexagonal bit socket
AC
2. Loosen the bolt completely. Then, remove the
steering wheel and air bag module assembly.
NOTE: Use a hexagonal bit socket or a hexagonal
wrench having an effective length of 75 mm or
more in the hexagonal section and the diameter of
8 mm or more.
REMOVAL AND INSTALLATION <INTENSE>
M1372011400194
WARNING
•
Before removing the steering wheel and air bag module assembly, refer to GROUP 52B,
Service Precautions (
) and Air Bag Module and Clock Spring (
).
•
Post-installation Operation
• Checking Steering Wheel Position with Wheels Straight
Ahead
AC211760AD
50 ± 5 N·m
2
1
2
When removing and installing the steering wheel, do not let it bump against the air bag
module.
Removal steps
<<
A
>>
1. Cover
<<
B
>>
2. Steering wheel and air bag module
assembly
STEERING WHEEL
POWER STEERING
37-19
NOTE: For air bag module removal, refer to GROUP
52B, Air Bag Module and Clock Spring
.
REMOVAL SERVICE POINTS
<<A>> COVER REMOVAL
AC211761AB
MB990784
Insert special tool ornament remover (MB990784) at
the indicated position to remove the cover.
NOTE: The special tool can be inserted through the
notch behind the area shown.
<<B>> STEERING WHEEL AND AIRBAG
MODULE ASSEMBLY REMOVAL
AC105823
AC304700
AC305145AB
A
Steering
wheel
Air bag module
connector
1. By sliding section A of the clock spring connector
as shown in the illustration in the arrow direction,
disconnect the connector.
AC211762 AC
Hexagonal bit
socket
2. Loosen the bolt completely. Then, remove the
steering wheel and airbag module assembly.
NOTE: Use a hexagonal bit socket or a hexagonal
wrench having an effective length of 75 mm or
more in the hexagonal section and the diameter of
8 mm or more.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст