Mitsubishi Lancer. Manual — part 190
SPECIAL TOOLS
POWER STEERING
37-8
SPECIAL TOOLS
M1372000600666
Tool
Number
Name
Use
AC106827
MB991897 or
MB992011
Ball joint remover
Knuckle and tie rod end ball joint
disconnection
NOTE: Steering linkage puller
(MB990635 or MB991113) is also
available to disconnect knuckle and
tie rod end ball joint.
MB990326
MB990326
Preload socket
Tie rod end ball joint turning torque
check
MB991548
MB991548
Power steering oil
pressure gauge
adapter (Pump
side)
Oil pump pressure test
MB991549
MB991549
Power steering oil
pressure gauge
adapter (Hose
side)
MB990662
MB990662
Power steering oil
pressure gauge
MB990784
MB990784
Ornament remover Cover removal
MB991006
MB990228 or
MB991006
Preload socket
Steering gear total pinion torque
check and adjustment
SPECIAL TOOLS
POWER STEERING
37-9
MB990607
Torque wrench
socket
• Rack support cover removal
<Invite>
• Rack support adjustment <Invite>
MB991621
MB991621
Piston driver
• Rack support cover removal
<Intense>
• Rack support adjustment
<Intense>
MB990925
MB990925
Bearing and oil
seal installer set
• Lower bearing removal
• Oil seal and bearing installation
• MB990927, MB990938, MB990939
(For details, refer to GROUP 26,
Special Tools
).
MB991120
MB991120
Needle bearing
puller
Needle bearing removal
MB991202
MB991202
Oil seal and
bearing installer
• Oil seal installation <Invite>
• Needle bearing installation
• Lower bearing installation
MB991199
AB
MB991199
Oil seal and
bearing installer
Oil seal installation <Intense>
MB991197
MB991197
Bar (long type)
Oil seal installation
MB991212
MB991212
MB991213
Oil seal protector
Rack installation
Tool
Number
Name
Use
MB991203
SPECIAL TOOLS
POWER STEERING
37-10
MB991203
Oil seal and
bearing installer
Oil seal and bearing installation
MB991317
MB991317
Seal ring installer
Seal rings installation
MB990941
MB990941
Torque tube
bearing installer
Lower oil seal installation
MB991561
MB991561
Boot band crimping
tool
Bellows band installation
MB990776
MB990776
Front axle base
Tie rod end ball joint dust cover
installation
Tool
Number
Name
Use
ON-VEHICLE SERVICE
POWER STEERING
37-11
ON-VEHICLE SERVICE
STEERING WHEEL FREE PLAY CHECK
M1372001000311
1. With the engine running (hydraulic operation), set
the front wheels straight ahead.
ACX01122 AB
2. Measure the play on the steering wheel
circumference before the wheels start to move
when slightly moving the steering wheel in both
directions.
Limit: 30 mm
3. When the play exceeds the limit, check for the
play on the steering shaft and steering linkage
connection. Correct or replace.
4. If the free play still exceeds the limit value, set the
steering wheel straight ahead with the engine
stopped. Load 5 N towards the steering wheel
circumference and check the play.
Standard value (steering wheel play with the
engine stopped): 10 mm or less
5. If the play exceeds the standard value, remove
the steering gear (Refer to
) and check
the total pinion torque (Refer to
).
STEERING ANGLE CHECK
M1372001100705
AC000756AB
1. Place the front wheel on a turning radius gauge
and measure the steering angle.
Standard value:
Inner
wheels
Invite
39
° 30' ± 1° 30'
Intense (LH
drive vehicles)
33
° 40' +1° 00'/-2° 00'
Intense (RH
drive vehicles)
37
° 00' +1° 00'/-2° 00'
Outer
wheels
(reference)
Invite
32
° 30'
Intense (LH
drive vehicles)
28
° 46'
Intense (RH
drive vehicles)
30
° 00'
2. If the steering angle is not within the standard
value, adjust the toe-in as follows.
Standard value:
at the centre of tyre tread: 1
± 2 mm
Toe angle (per wheel): 0
° 03' ± 06'
AC006074 AD
Lock nut
Clip
3. Loosen the lock nut, and unclip the bellows clip.
4. Adjust the toe-in by turning the left and right tie
rod turnbuckles by the same amount (in opposite
directions).
NOTE: The toe will move out as the left turnbuckle
is turned toward the front of the vehicle and the
right turnbuckle is turned toward the rear of the
vehicle.
5. Tighten the lock nut to the specified torque, and
tighten the bellows by the clip.
Tightening torque: 40
± 5 N⋅ m
6. Recheck the steering angle.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст