Mitsubishi Lancer. Manual — part 247

DOOR MIRROR

EXTERIOR

51-50

DOOR MIRROR

REMOVAL AND INSTALLATION

M1511006400308

AC304733

Note

: Claw positions

AB

A

A

Section A – A

Claw

1

2

1

2

3

4

5

6

7

8

Door mirror removal steps
1. Cover
2. Delta inner cover
3. Harness connector <Vehicles with

remote controlled mirror>

4. Door mirror assembly
5. Door mirror body assembly

<<

A

>> >>

A

<< 6. Mirror

Remote controlled mirror switch
removal steps
7. Instrument panel ornament (Refer to

GROUP 52A, Instrument panel

P.52A-3

.)

8. Remote controlled mirror switch

REMOVAL SERVICE POINT
<<A>> MIRROR REMOVAL

AC000441

00007256

Mirror

Flat-tipped
screwdriver

Section A – A

Pivot plate

Notch

Protective
tape

A
A

A
A

AE

DOOR MIRROR

EXTERIOR

51-51

Push the top of the mirror with your hand to tilt it and
attach the protective tape as shown in the illustration.
Then insert a flat-tipped screwdriver in between the
notch at the rear of the mirror and the pivot plate, and
disengage the bottom of the mirror.

INSTALLATION SERVICE POINT
>>A<< MIRROR INSTALLATION

AC000442

00007258

Mirror

Flat-tipped
screwdriver

Section A – A

Pivot plate

A
A

A
A

AB

While supporting the clip position on the underside of
the pivot plate with a flat-tipped screwdriver, press
the clip at the front of the mirror to engage the bottom
of the mirror.

INSPECTION

M1511006500286

ELECTRIC REMOTE CONTROL MIRROR
OPERATION CHECK <VEHICLES WITH-
OUT HEATED DOOR MIRROR>

3

2

1

AC005969

Check that the mirror moves as described in the
table when each terminal is connected to the battery.

Battery connection

Direction
operation

• Connect terminal 1 to the negative

battery terminal.

• Connect terminal 3 to the positive

battery terminal.

Mirror
glass
should face
upward

• Connect terminal 3 to the negative

battery terminal.

• Connect terminal 1 to the positive

battery terminal.

Mirror
glass
should face
downward

• Connect terminal 1 to the negative

battery terminal.

• Connect terminal 2 to the positive

battery terminal.

Mirror
glass
should face
to the right

• Connect terminal 2 to the negative

battery terminal.

• Connect terminal 1 to the positive

battery terminal.

Mirror
glass
should face
to the left

DOOR MIRROR

EXTERIOR

51-52

ELECTRIC REMOTE CONTROL MIRROR
OPERATION CHECK <VEHICLES WITH
HEATED DOOR MIRROR>

AC202548

1

4 5 6 7

2 3

Check that the mirror moves as described in the
table when each terminal is connected to the battery.

Battery connection

Direction
operation

• Connect terminal 5 to the negative

battery terminal.

• Connect terminal 7 to the positive

battery terminal.

Mirror
glass
should face
upward

• Connect terminal 7 to the negative

battery terminal.

• Connect terminal 5 to the positive

battery terminal.

Mirror
glass
should face
downward

• Connect terminal 5 to the negative

battery terminal.

• Connect terminal 6 to the positive

battery terminal.

Mirror
glass
should face
to the right

• Connect terminal 6 to the negative

battery terminal.

• Connect terminal 5 to the positive

battery terminal.

Mirror
glass
should face
to the left

DOOR MIRROR CONTROL SWITCH CON-
TINUITY CHECK

AC005970

2

1

4

3

5

10

9

8

7

6

11

Switch position

Tester
connection

Specified
condition

OFF

9

− 2, 9 − 3, 9 − 6, 9

− 10, 9 − 11, 1 − 2,

1

− 3, 1 − 6, 1 − 10,

1

− 11

Open circuit

Left side OFF

9

− 6, 9 − 10, 9 −

11, 1

− 6, 1 − 10, 1

− 11

Open circuit

Up

1

− 6, 9 − 11

Less than 2
ohms

Down

1

− 11, 6 − 9

Right

1

− 6, 9 − 10

Left

1

− 10, 6 − 9

Right
side

OFF

9

− 2, 9 − 3, 9 − 6, 1

− 2, 1 − 3, 1 − 6

Open circuit

Up

1

− 6, 3 − 9

Less than 2
ohms

Down

1

− 3, 6 − 9

Right

1

− 6, 2 − 9

Left

1

− 2, 6 − 9

HEATED DOOR MIRROR CHECK

CAUTION

When relocating the car between locations with
extremely different temperatures (warm and
cold), leave the car in the location for a while to
adapt to the temperature prior to checking it.

AC202548

1

4 5 6 7

2 3

The resistance value between door mirror connector
terminals 1 and 4 should meet the standard value
with the ambient temperature at steady 25

° C.

Standard value: 5.9

− 7.8 Ω

31-1

GROUP 31

WHEEL AND TYRE

CONTENTS

GENERAL INFORMATION . . . . . . . .

31-2

SERVICE SPECIFICATIONS. . . . . . .

31-2

TROUBLESHOOTING . . . . . . . . . . . .

31-3

DIAGNOSIS . . . . . . . . . . . . . . . . . . . . . . . .

31-3

WHEEL BALANCE ACCURACY . . . . . . . .

31-4

ON-VEHICLE SERVICE . . . . . . . . . . .

31-7

TYRE INFLATION PRESSURE CHECK . . .

31-7

TYRE WEAR CHECK . . . . . . . . . . . . . . . . .

31-7

WHEEL RUNOUT CHECK . . . . . . . . . . . . .

31-7

WHEEL AND TYRE . . . . . . . . . . . . . .

31-7

INSTALLATION SERVICE POINT . . . . . . .

31-7