Mitsubishi Lancer. Manual — part 229
DOOR
BODY
42-38
Actuator Switch Check <Driver’s side>
Lever position
Tester
connection
Specified
condition
At the "LOCK"
position
1
− 2
Less than 2
ohms
1
− 3
Open circuit
At the "UNLOCK"
position
1
− 2
Open circuit
1
− 3
Less than 2
ohms
REAR DOOR LOCK ACTUATOR CHECK
2 3
4
1
5 6
2 3
4
1
5 6
AC305112
B
A
AB
Rear door
Lock
Unlock
View A
View B
Unlock
Lock
<Left side>
<Right side>
Lever
Lever
Actuator Operation Check
Lever
position
Battery connection Lever
operation
At the
"LOCK"
position
• Connect terminal
No. 4 and the
negative battery
terminal.
• Connect terminal
No. 6 and the
positive battery
terminal.
The lever
moves from the
"LOCK"
position to the
"UNLOCK"
position.
At the
"UNLOCK"
position
• Connect terminal
No. 6 and the
negative battery
terminal.
• Connect terminal
No. 4 and the
positive battery
terminal.
The lever
moves from the
"UNLOCK"
position to the
"LOCK"
position.
DOOR LOCK KEY CYLINDER SWITCH
CHECK <PASSENGER’S SIDE>
AC101318
3
2
1
Switch
position
Tester
connection
Specified
condition
LOCK
2
− 3
Less than 2
ohms
NEUTRAL
(OFF)
1
− 2, 2 − 3
Open circuit
UNLOCK
1
− 2
Less than 2
ohms
DOOR
BODY
42-39
WINDOW GLASS RUNCHANNEL AND
DOOR OPENING WEATHERSTRIP
REMOVAL AND INSTALLATION
M1423003100290
<FRONT DOOR>
AC304409AB
Section A – A
<Front door>
Sealant: 3M ATD Part No.8633 or equivalent
Door
: Sectional view of
clip position
: Sectional view of
clip position
6
2
1
4
3
6
5
A
A
1
Waterproof film removal steps
• Door trim assembly, speaker (Refer to
GROUP 52A, Trims
1. Waterproof film
Door inner opening weatherstrip
removal steps
• Scuff plate, centre pillar lower trim
and cowl side trim (Refer to GROUP
52A, Trims
.)
2. Door inner opening weatherstrip
(Body side)
Door outer opening weatherstrip
removal steps
• Front door check mounting bolt (Door
side) (Refer to
<<
A
>> >>
A
<< 3. Door outer opening weatherstrip
Door window glass runchannel
removal
4. Door window glass runchannel
Door beltline inner weatherstrip
removal steps
• Front door trim(Refer to GROUP 52A,
Door trim
.)
5. Door beltline inner weatherstrip
Door beltline moulding removal steps
• Door mirror assembly (Refer to
GROUP 51, Door mirror
• Door window glass (Refer to
.)
6. Door beltline moulding
DOOR
BODY
42-40
<REAR DOOR>
AC304418AB
Section A – A
Door
: Sectional view of
clip position
: Sectional view of
clip position
7
2
4
5
7
A
A
3
Section B – B
<Rear door>
Door
4
3
6
B
B
Sealant: 3M ATD Part No.8633 or equivalent
1
1
Waterproof film removal steps
• Door trim assembly (Refer to GROUP
52A, Door trim
).
1. Waterproof film
Door inner opening weatherstrip
removal steps
• Scuff plate, centre pillar lower trim
and cowl side trim (Refer to GROUP
52A, Trims
.)
2. Door inner opening weatherstrip
(Body side)
Door outer opening weatherstrip
removal steps
• Rear door check mounting bolt (Door
side) (Refer to
3. Retainer weatherstrip
<<
A
>> >>
A
<< 4. Door outer opening weatherstrip
Door window glass runchannel
removal
5. Door window glass runchannel
Door beltline inner weatherstrip
removal steps
• Rear door trim (Refer to GROUP 52A,
Door trim
.)
6. Door beltline inner weatherstrip
Door beltline moulding removal steps
• Door window glass (Refer to
.)
• Stationary glass (Refer to
7. Door beltline moulding
TRUNK LID
BODY
42-41
REMOVAL SERVICE POINT
<<A>> DOOR OUTER OPENING WEATH-
ERSTRIP REMOVAL
ACX00555
15 mm
8 mm
AB
4 mm
Thickness:
1 mm
Fabricated
tool
Make a fabricated tool as shown in the illustration to
remove the door weatherstrip.
INSTALLATION SERVICE POINT
>>A<< DOOR OUTER OPENING WEATH-
ERSTRIP INSTALLATION
The clip colour identifies the left and right weather-
strips so be sure to use the colours so as to install
correctly.
Applicable side
Identification colour
Right door
Pink
Left door
Natural (White)
TRUNK LID
SPECIAL TOOL
M1421000600245
Tool
Number
Name
Use
MB991244
MB991244
Torsion bar remover and
installer
Removal and installation of
trunk lid torsion bar
ON-VEHICLE SERVICE
TRUNK LID ADJUSTMENT
M1421001000042
1. If the clearance around the trunk lid panel
assembly is not uniform and locking and
unlocking of the trunk lid is difficult, make
adjustments to the trunk lid bumpers (refer to
) and trunk lid hinges (refer to
).
2. If the clearance around the trunk lid panel
assembly is uniform, but locking and unlocking of
the trunk lid is difficult, make adjustments to the
trunk lid bumpers (refer to
) and trunk lid
striker (refer to
).
AC202324
AC202325
AC202913
A
A
A
A
AB
Section A – A
Trunk lid panel assembly
Side outer panel
Trunk lid panel
assembly
Side outer panel
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст