Mitsubishi Lancer. Manual — part 62
1-2
AFTER ROAD TEST . . . . . . . . . . . . .
33. IDLE SPEED . . . . . . . . . . . . . . . . . . . . .
34. IGNITION TIMING. . . . . . . . . . . . . . . . .
35. RADIATOR COOLANT LEVEL . . . . . . .
36. HOSES, FLUID LINES AND CONNECTIONS
LOCATED UNDER HOOD . . . . . . . . . . . . .
37. MANUAL TRANSMISSION AND
TRANSFER (4WD) OIL LEVEL . . . . . . . . .
38. AUTOMATIC TRANSMISSION FLUID
LEVEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
39. ENGINE, TRANSMISSION, STEERING GEAR
BOX AND DIFFERENTIAL FOR LEAKS . .
40. FRONT AND REAR DIFFERENTIAL OIL
LEVELS . . . . . . . . . . . . . . . . . . . . . . . . . . . .
41. HOSES, FLUID LINES AND CONNECTIONS
LOCATED UNDER VEHICLE . . . . . . . . . . .
FINAL STEPS . . . . . . . . . . . . . . . . . . .
42. HEADLAMP AIMING . . . . . . . . . . . . . . .
43. EQUIPMENT . . . . . . . . . . . . . . . . . . . . .
44. EXTERIOR AND INTERIOR . . . . . . . . .
45. OWNER INSTRUCTIONS. . . . . . . . . . .
NOTES CONCERNING ENTRIES
PRE-DELIVERY INSPECTION
1-3
NOTES CONCERNING ENTRIES
M6010100100080
This section describes the details and the inspection methods employed for the pre-delivery inspection of
vehicles.
The inspection should be conducted according to the sequence described in the TABLE OF PRE-DELIVERY
INSPECTION.
Inspection methods are described following the TABLE OF PRE-DELIVERY INSPECTION.
NOTE:
.
1. The spaces for model, C/# (Chassis number), E/# (engine number), aggregate distance travelled in kilo-
metres (miles), date of inspection, name of person conducting the inspection, and body colour must be
completed without fail.
2. The spaces for place of inspection, and name of owner should be completed as required.
AC306353
AC401525
TABLE OF PRE-DELIVERY INSPECTION
INSPECTION PROCEDURE
First Step
Body
Under Hood
Under Vehicle
Before Road Test
Model
Chassis number
Engine number
Distance Travelled
km
Owner
Date of inspection
Place of inspection
Inspector
Body colour
Symbols to be used
Needs
adjustment
Good
A
T
L
X
C
Needs
cleaning
Needs
replenishment
of lubricant,
water, etc.
Needs
replenishment
of repair
Needs
retightening
1. Connection of the dark current connector
Road Test
27. Engine performance and exhaust gas
After Road Test
33. Idle speed
Final Steps
42. Headlamp aiming
43. Equipment
44. Exterior and interior
45. Owner instructions
34. Ignition timing
35. Radiator coolant level
36. Hoses, fluid lines and connections located under hood
37. Manual transmission and transfer (4WD) oil level
38. Automatic transmission fluid level
39. Engine, transmission, steering gear box and
differential for leaks
40. Front and rear differential oil levels
41. Hoses, fluid lines and connections located under vehicle
28. Transmission in all ranges
29. Brakes
30. Steering control
31. Vibration and rattles
32. Electrical equipment
2. Wrap film
3. Exterior
4. Operation of door locking systems and door hinges
5. Operation of door mirrors, windows and sunroof
6. Engine oil level
7. Brake master cylinder fluid level
8. Clutch master cylinder fluid level
9. Washer fluid level
10. Battery condition and connections
11. Power steering fluid level
12. Electrical wiring
13. Tyre and spare tyre pressures
14. Suspension system
15. Steering linkage and split pins
16. Under body
17. Seat adjusters and seat back latches
18. Choke system and inhibitor switch
19. Idle control knob
20. Instrument panel controls
21. Meters, gauges, warning lamps and indication lamps
22. Air conditioning, heater and defroster systems
23. Wipers and washers
24. Operation of service brakes and parking brakes
25. Clutch operation
26. Operation of seat belts, shoulder belts and retractors
NOTES CONCERNING ENTRIES
PRE-DELIVERY INSPECTION
1-4
PAINTWORK TERMS
PRE-DELIVERY INSPECTION
1-5
PAINTWORK TERMS
M6010200100032
Term
Definition
Remarks
Blister
A raised bubble in the paint (from the base
or the undercoat) caused by abnormal
moisture. The bubble may contain either
water or air.
Change in tone
The colour tone of the painted surface is not
uniform.
Including wrong colour, discoloration and
decoloration.
Contact mark
A mark on the painted surface as a result of
contact by hands or clothing at the time of
paint application.
Crack
A crack in the painted surface.
Cracks may be either shallow or deep.
Dirt in paintwork
Rough surface resulting from foreign
material in the paint or from dust deposited
on wet paint during painting or storage.
Filed or ground
traces
Deep scratches in sheet metal surface,
resulting from improper use of buffer or
sander, are not completely covered, and are
visible through paint coating.
Orange peel
The painted surface has the appearance of
an orange peel.
Peeling
The paint flakes off (partly or over a wide
area).
The peeling may be minor, medium, or
major.
Pin holes
Tiny holes in the painted surface.
Runs
A visible trickle of dried paint on the surface. Either undercoat or top-coat.
Scratches
Scratches on the painted surface.
Shrink
The painted surface "shrinks", causing
wrinkles.
Smears
Spots of soot or other material deposited on
the painted surface.
Including stains and water spots.
Spray mist
The painted surface includes fine particles of
other paint.
Uneven lustre
The lustre of the painted surface is not
uniform.
Uneven metallic
dispersion
The metallic dispersion of the painted
surface is not uniform.
Visibly incomplete
topcoating
A part of the undercoating visible.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст