Mitsubishi Lancer. Manual — part 237
AC304340
1
1
A
A
A
A
AB
B
B
C
C
C
C
B
B
N
N
N
2
N
2
4
3
N
3
N
4
N
6
9
7
N
6
N
N
7
N
N
9
<Wagon>
<Vehicle with roof rail>
<Vehicle without roof rail>
Removal steps
<<
A
>> >>
C
<< 1. Roof drip moulding
>>
B
<< 2. Front drip moulding clip A
>>
B
<< 3. Front drip moulding clip B
>>
B
<< 4. Front drip moulding clip C
>>
B
<< 5. Rear drip moulding clip
>>
A
<< 6. Drip moulding clip A
>>
A
<< 7. Drip moulding clip B
>>
A
<< 8. Drip moulding clip C
9. Roof drip moulding clip
MOULDINGS
EXTERIOR
51-10
REMOVAL SERVICE POINT
<<A>> ROOF DRIP MOULDING REMOVAL
CAUTION
If the moulding has become warped, it should not
be reused.
AC304375
MB990449
AB
Use special tool window moulding remover
(MB990449) to lever out the moulding.
MOULDINGS
EXTERIOR
51-11
INSTALLATION SERVICE POINTS
>>A<< DRIP MOULDING CLIP C/DRIP
MOULDING CLIP B/DRIP MOULDING
CLIP A INSTALLATION
1. The drip moulding clips A, B and C differ
according to where they are used, so check the
identification colour before installation.
Applicable location
Identification colour
Drip moulding clip A
Yellow
Drip moulding clip B
Blue
Drip moulding clip C
Milky white
AC003629
Front pillar outer
Portion B
Portion A
AD
2. After installing the clip to the front pillar outer in
alignment with its portion A, cut from portion B.
>>B<< REAR DRIP MOULDING
CLIP/FRONT DRIP MOULDING CLIP
C/FRONT DRIP MOULDING CLIP
B/FRONT DRIP MOULDING CLIP A
INSTALLATION
The front drip moulding clips A, B, C and rear drip
moulding clip differ according to where they are
used, so check the identification colour before instal-
lation.
Applicable location
Identification colour
Front drip moulding clip A Orange
Front drip moulding clip B Purple
Front drip moulding clip C Blue
Rear drip moulding clip
Grey
>>C<< ROOF DRIP MOULDING
INSTALLATION
Install the clips to the roof drip moulding before
installing the moulding to the vehicle body.
AC504986
AC400117
AC400128
Section A – A
DOOR MOULDINGS
Section B – B
Section C – C
AB
A
A
C
C
B
B
2
1
3
Clip
Clip
Boss
AC400840
AE
Double-sided tape: Generic products [ a: 6 mm width and 1.2 mm thickness,
b: 20 mm width and 1.2 mm thickness ]
1
2
3
a
b
b
a
Adhesive tape affixed location
Front fender moulding removal
<<
A
>> >>
A
<< 1. Front fender moulding
Door moulding removal steps
<<
A
>> >>
A
<< 2. Front door moulding
<<
A
>> >>
A
<< 3. Rear door moulding
MOULDINGS
EXTERIOR
51-12
REMOVAL SERVICE POINT
<<A>> FRONT FENDER, FRONT AND
REAR DOOR MOULDINGS REMOVAL
Gently lift and remove the door moulding. If there is
any double-sided tape remaining on the door mould-
ing, remove according to the following instructions.
<Remove double-sided tape remaining on the body
surface>
AC000420
Double-sided tape
Protection tape
AB
MOULDINGS
EXTERIOR
51-13
1. Attach protection tape all the way along the edges
of the double-sided tape which is still adhering to
the body.
AC000421
Double-sided tape
AB
2. Use a resin spatula to scrape off the double-sided
tape.
3. Peel off the protection tape.
4. Wipe the body surface and clean it with a rag
moistened with isopropyl alcohol.
<Remove double-sided tape remaining on door
moulding and adhere double-sided tape (when
re-using door moulding)>
AC313343
1. Scrape off the double-sided tape on the door
moulding with a resin spatula as possible.
2. Wipe the door moulding surface and clean it with
a rag moistened with isopropyl alcohol.
3. Remove only a small portion of the residual
adhesive.
4. Adhere the double-sided tape as specified on the
door moulding.
INSTALLATION SERVICE POINT
>>A<< FRONT FENDER, FRONT AND
REAR DOOR MOULDINGS INSTALLA-
TION
AC313344
Backing paper
Adhesive tape
AB
1. Tear off the double-sided tape backing paper.
NOTE: If attach the adhesive tape to the edge of
the backing paper, it will be easy to tear off.
2. Install the clips to the front and rear door
mouldings before installing them to the vehicle
body.
3. Install the door mouldings.
NOTE: If the double-sided tape is difficult to affix
in cold temperature, etc., warm the bonding sur-
faces of the body and door mouldings to about 40
−
60
°
C before affixing the tape.
4. Firmly press in the door mouldings onto the
respective body surfaces.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст