Mitsubishi Lancer. Manual — part 244
REAR WIPER AND WASHER <Wagon>
EXTERIOR
51-38
2. Disconnect the battery cable from the rear
windshield wiper motor while it is turning and then
check to see that the motor stops.
3. Re-connect the battery as shown in Figure (B).
4. Check to see that the rear windshield wiper motor
runs and then stops at the automatic stop
position.
REAR WASHER MOTOR CHECK
1
2
AC005900
1. Remove the rear washer tank assembly with the
washer hose attached. Then fill the washer tank
with water.
2. Check to see that the water is vigorously sprayed
when connecting the positive battery terminal to
terminal number 2 and terminal number 1 to the
negative battery terminal.
REAR WASHER FLUID EJECTION CHECK
CAUTION
Take care not to damage the nozzle when insert-
ing the flat-tipped screwdriver into it.
AC304544AC
Unit: mm
57 84
125
6
Section A – A
A
A
High-mounted
stop lamp
Rear washer nozzle
Flat-tipped screwdriver
Ceramic line terminal
Washer nozzle
perpendicular
For the vertical aiming of washer nozzle, insert the
flat-tipped screwdriver into the nozzle and move it to
the arrow direction.
REAR WIPER AND WASHER SWITCH
CHECK
1
6
8
11
10
9
7
5
4
3
2
AC000417
Check continuity between the switch terminals.
Switch position
Tester
connection
Specified
condition
OFF
4
− 6, 5 − 6
Open circuit
Rear wiper switch 4
− 6
Less than 2
ohms
Rear washer
switch
5
− 6
HEADLAMP WASHER <LH drive vehicles>
EXTERIOR
51-39
HEADLAMP WASHER <LH drive vehicles>
TROUBLESHOOTING
M1511000700356
The headlamp washer is controlled by the Smart Wir-
ing System (SWS). For troubleshooting, refer to
GROUP 54B, Troubleshooting
or GROUP
54C, Troubleshooting
HEADLAMP WASHER
REMOVAL AND INSTALLATION
M1511009700063
AC304608
AB
10
N
2
4
5
6
8
7
1
9
11
9
1
10
N
4.9 ± 0.7 N·m
4.9 ± 0.7 N·m
3
Removal steps
•
Washer fluid draining
1.
Headlamp washer hose connection
2.
Under cover side panel (RH)
3.
Splash shield mounting clip (RH)
4.
Headlamp washer motor
connection
5.
Headlamp washer joint
6.
Headlamp washer hose
7.
Headlamp washer motor
Removal steps (Continued)
HEADLAMP WASHER <LH drive vehicles>
EXTERIOR
51-40
INSPECTION
M1511009800082
HEADLAMP WASHER MOTOR CHECK
AC304136 AB
1 2
1. Remove the headlamp washer motor connector.
2. Check to see that the water is vigorously sprayed
when connecting the positive battery terminal to
terminal number 1 and terminal number 2 to the
negative battery terminal.
8.
Headlamp washer gasket
•
Front bumper (Refer to
9.
Headlamp washer actuator
assembly
10. O-ring
11. Headlamp washer hose assembly
Removal steps (Continued)
MARK
EXTERIOR
51-41
MARK
REMOVAL AND INSTALLATION
M1511011801435
AC504923
1
1
2
2
3
AC
<Sedan>
<Wagon>
3
Removal
>>A<<
1. Front three-diamond mark (Refer to
>>
A
<< 2. Rear three-diamond mark
>>
A
<< 3. Lancer mark
INSTALLATION SERVICE POINT
>>A<< MARK APPLICATION
1. Installation position
Attach each mark to the position shown in the
illustration.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст