Mitsubishi Lancer. Manual — part 181
GENERAL INFORMATION
FRONT AXLE
26-2
GENERAL INFORMATION
M1261000100648
The front axle consists of front hubs, knuckles, wheel
bearings and driveshafts, and has the following fea-
tures:
• The wheel bearing is a double-row angular con-
tact ball bearing which incorporates the oil seals
and is highly resistant to thrust loads.
• The driveshaft incorporates BJ-TJ type constant
velocity joints with high transmission efficiency for
low vibration and noise.
• The dynamic damper has been mounted on the
driveshaft to reduce differential gear noise.
• ABS rotor for detecting the wheel speed is
press-fitted to the BJ.
NOTE:
.
•
TJ: Tripod Joint
•
BJ: Birfield Joint
SPECIFICATIONS
Item
1300, 1600
2000
Wheel bearing Type
Double-row angular contact ball bearing
Bearing (OD x ID) mm
80 x 40
80 x 40
Driveshaft
Joint type
Outer
BJ
BJ
Inner
TJ
TJ
Length (joint to joint)
×
diameter mm
LH
375.9
× 24
375.9
× 24
RH
699
× 24 (1600-M/T),
703.2
× 23 (1300-M/T,
1600-A/T)
700
× 24 (M/T)
699
× 24 (A/T)
CONSTRUCTION DIAGRAM
AC303569
Front hub
Knuckle
Strut assembly
TJ (LH)
Driveshaft (LH)
Dynamic damper
BJ
Wheel bearing
Driveshaft (RH)
TJ (RH)
AB
ABS rotor
Dynamic damper
SERVICE SPECIFICATIONS
FRONT AXLE
26-3
SERVICE SPECIFICATIONS
M1261000300675
Item
Standard value
Limit
Wheel bearing axial play mm
−
0.05
Hub starting torque N
⋅ m
−
1.8
Protruding length of stabilizer bar mounting bolt mm
22
± 1.5
−
Setting of TJ boot length mm
1300-RH, 1600-A/T-RH 85
± 3
−
1300-LH, 1600-M/T,
1600-A/T-LH, 2000
90
± 3
−
Opening dimension of the
special tool (MB991561) mm
When the BJ boot band
(small) is crimped
2.9
−
When the BJ boot band
(large) is crimped
2.9
−
Crimped width of the BJ boot band mm
2.4
− 2.8
−
LUBRICANTS
M1261000400735
Item
Specified lubricant
Quantity
TJ boot grease
Repair kit grease
1300-LH, 1600-LH,
2000-LH
120
± 10 g
1300-RH, 1600-A/T-RH
110
± 10 g
1600-M/T-RH, 2000-A/T-RH 120
± 10 g
2000-M/T-RH
105
± 10 g
BJ boot grease
Repair kit grease
95
± 10 g
SPECIAL TOOLS
FRONT AXLE
26-4
SPECIAL TOOLS
M1261000600773
Tool
Number
Name
Use
B990767
MB990767
Front hub and end
yoke holder
Fixing of the hub
MB991618
MB991618
Hub bolt remover Removal of the hub bolt
AC106827
MB991897 or
MB992011
Ball joint remover Knuckle and tie rod end ball joint
disconnection
NOTE: Steering linkage puller
(MB990635 or MB991113)is also used
to disconnect knuckle and tie rod end
ball joint.
MB990241AB
A
B
MB990241
A: MB990242
B: MB990244
Axle shaft puller
A: Puller shaft
B: Puller bar
Removal of the driveshaft
MB991354
MB991354
Puller body
MB991056 or
MB991355
Knuckle arm
bridge
• Removal of the hub
• Removal of the wheel bearing
AC100320AB
A
B
C
A: MB991017
B: MB990998
C: MB991000
A, B: Front hub
remover and
installer
C: Spacer
• Removal of the hub
• Provisional holding of the wheel
bearing
• Measurement of hub starting torque
• Measurement of wheel bearing axial
play
NOTE: MB991000, which belongs to
MB990998, should be used as a
spacer.
SPECIAL TOOLS
FRONT AXLE
26-5
MB990685
Torque wrench
Measurement of hub starting torque
MB990326
MB990326
Preload socket
MB990810
MB990810
Side bearing
puller
• Removal of the centre bearing
bracket
• Removal of the wheel bearing inner
race (outside)
MB991460
Plug
Prevention of transmission fluid drain
and of entry of foreign objects
MB991561
MB991561
Boot band
crimping tool
BJ boot (resin boot) band installation
MB990925
MB990925
Bearing and oil
seal installer set
• Removal of the wheel bearing
• Removal and installation of the
centre bearing
• Press-fitting of the dust seal outer,
inner
MB990890
MB990890
Rear suspension
bushing base
• Installation of the wheel bearing
• Press-fitting of the dust seal outer,
inner
MB990883
MB990883
Rear suspension
bushing arbor
Installation of the wheel bearing
Tool
Number
Name
Use
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст