Dodge Dakota (ND). Manual — part 193
U0024-CAN B BUS (-) CIRCUIT OPEN (CONTINUED)
For a complete wiring diagram Refer to Section 8W.
•
When Monitored:
With the ignition on and battery voltage between 10 and 16 volts.
•
Set Condition:
The FCM detects the (D54) CAN B Bus (-) circuit is open.
Possible Causes
CAN B BUS TERMINAL PUSH OUT
SPREAD CAN B BUS TERMINAL
(D54) CAN B BUS (-) CIRCUIT OPEN
INTERNAL OPEN IN A CAN B BUS MODULE
Diagnostic Test
1.
TEST FOR INTERMITTENT CONDITION
Turn the ignition on.
With the scan tool, record and erase FCM DTC’s
Cycle the ignition from on to off 3 times.
Turn the ignition on.
With the scan tool, read active FCM DTC’s.
Does the scan tool display this DTC as active?
Yes
>> Go To 2
No
>> The conditions that caused this code to set are not present at this time. Using the wiring diagram/sche-
matic as a guide, inspect the wiring and connectors.
8E - 28
ELECTRONIC CONTROL MODULES - ELECTRICAL DIAGNOSTICS
ND
U0024-CAN B BUS (-) CIRCUIT OPEN (CONTINUED)
2.
ATTEMPT TO ISOLATE THE OPEN CONDITION
Turn the ignition on.
Verify that all CAN B Bus modules are communicating with the scan
tool.
NOTE: A red X will be next to the module that is not communi-
cating, indicating that the module is not active on the Bus net-
work. A green check indicates that the module is active on the
Bus network.
NOTE: If any module is not communicating, perform the appropri-
ate no response test procedure before proceeding.
Turn the ignition off.
Gain access to the Front Control Module C1 harness connector, but
do not disconnect.
Using a fused jumper wire, connect one end to ground and with the
other end backprobe the CAN B Bus (+) circuit at the FCM C1 har-
ness connector.
Turn the ignition on.
With the scan tool monitor the network status screen and document all modules that display a red X.
Are there any red X’s displayed next to the modules?
Yes
>> Go To 3
No
>> Check backprobe connection to ground, make sure it is proper. The CAN B Bus open DTC may no
longer be active, it may be stored. Check all module connections
Perform BODY VERIFICATION TEST - VER 1. (Refer to BODY VERIFICATION TEST - VER 1).
3.
ATTEMPT TO ISOLATE THE OPEN CONDITION — MULTIPLE RED X’S
With the scan tool continue monitoring the network status screen.
Are there multiple red X’s displayed next to the modules?
Yes
>> The most likely cause of this condition is an open CAN B Bus (-) circuit between a common CAN B Bus
splice and the modules that display the red X next to them. Use the wiring diagrams will help you deter-
mine where open condition exists.
Perform BODY VERIFICATION TEST - VER 1. (Refer to BODY VERIFICATION TEST - VER 1).
No
>> Go To 4
ND
ELECTRONIC CONTROL MODULES - ELECTRICAL DIAGNOSTICS
8E - 29
U0024-CAN B BUS (-) CIRCUIT OPEN (CONTINUED)
4.
(D54) CAN B BUS (-) CIRCUIT OPEN — SINGLE RED X
Turn the ignition off.
Disconnect the module that has the red X displayed next to it.
Turn the ignition on.
Measure the voltage between the (D54) CAN B Bus (-) circuit and ground.
Is there any voltage present?
Yes
>> Inspect the connector and terminal for damage, inspect for spread terminals, or push out terminals. If
ok, replace the module that displayed the red X next to it in accordance with the service information.
Perform BODY VERIFICATION TEST - VER 1. (Refer to BODY VERIFICATION TEST - VER 1).
No
>> Repair the (D54) CAN B Bus (-) circuit for an open between the next common splice and the module
that has the red X displayed next to it. Use the wiring diagrams will help you determine where open
condition exists.
Perform BODY VERIFICATION TEST - VER 1. (Refer to BODY VERIFICATION TEST - VER 1).
8E - 30
ELECTRONIC CONTROL MODULES - ELECTRICAL DIAGNOSTICS
ND
U0025-CAN B BUS (-) CIRCUIT LOW
ND
ELECTRONIC CONTROL MODULES - ELECTRICAL DIAGNOSTICS
8E - 31
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст