Dodge Dakota (ND). Manual — part 111
C2202-ORIGINAL VIN MISMATCH / MISSING (340)
For a complete wiring diagram Refer to Section 8W.
•
When Monitored:
Ignition on.
•
Set Condition:
This DTC will set if the current VIN does not match the broadcast VIN.
Possible Causes
ICOMMUNICATIONS DTC(S) PRESENT
POWERTRAIN CONTROL MODULE
ANTI-LOCK BRAKE MODULE
Diagnostic Test
1.
DTC IS ACTIVE
Turn the ignition on.
With the scan tool, erase DTCs.
Turn the ignition off.
Turn the ignition on.
Wait ten seconds.
With the scan tool, select View DTCs.
Is the status Active for this DTC?
Yes
>> Go To 2
No
>> Go To 3
2.
WRONG VIN PROGRAMMED IN PCM
Turn the ignition on.
With the scan tool, read the VIN in the PCM.
Compare VIN in the PCM to the vehicle VIN.
Is the correct VIN programmed in the PCM?
Yes
>> Replace the Antilock Brake Module in accordance with the Service Information.
Perform ABS VERIFICATION TEST - VER 1. (Refer to 5 - BRAKES/ELECTRICAL - DIAGNOSIS AND
TESTING)
No
>> Replace the Powertrain Control Module in accordance with the Service Information.
Perform ABS VERIFICATION TEST - VER 1. (Refer to 5 - BRAKES/ELECTRICAL - DIAGNOSIS AND
TESTING)
5 - 214
BRAKES - ABS ELECTRICAL DIAGNOSTICS
ND
C2202-ORIGINAL VIN MISMATCH / MISSING (340) (CONTINUED)
3.
COMMUNICATION DTCS PRESENT
Turn the ignition off.
With the scan tool, read DTCs in all other modules. If any communications DTCs are present, refer to the appro-
priate diagnostic procedure.
Refer to any Technical Service Bulletins that may apply.
Were any problems found?
Yes
>> Repair as necessary.
Perform ABS VERIFICATION TEST - VER 1. (Refer to 5 - BRAKES/ELECTRICAL - DIAGNOSIS AND
TESTING)
No
>> Test Complete.
ND
BRAKES - ABS ELECTRICAL DIAGNOSTICS
5 - 215
C2206-VEHICLE CONFIGURATION MISMATCH (340)
For a complete wiring diagram Refer to Section 8W.
•
When Monitored:
Ignition on.
•
Set Condition:
This DTC will set if the vehicle type is not identified or incorrectly identified.
Possible Causes
ANTI-LOCK BRAKE MODULE
Diagnostic Test
1.
ANTI-LOCK BRAKE MODULE
NOTE: Diagnose and repair any Powertrain Control Module VIN or Communication DTCs before continuing
with this test.
NOTE: If C2202–Original VIN Mismatch / Missing is set along with this DTC, perform the diagnostic proce-
dure for C2202 before continuing with this test.
Turn the ignition on.
With the scan tool, clear DTCs.
Turn the ignition off.
Turn the ignition on.
With the scan tool, select View DTCs.
Is the status Active for this DTC?
Yes
>> Replace the Antilock Brake Module in accordance with the Service Information.
Perform ABS VERIFICATION TEST - VER 1. (Refer to 5 - BRAKES/ELECTRICAL - DIAGNOSIS AND
TESTING)
No
>> Use the scan tool to read DTCs in all other modules. If any communication DTCs are present, perform
the appropriate diagnostic procedure. Refer to any Technical Service Bulletins that apply. If no problems
are found, test is complete.
5 - 216
BRAKES - ABS ELECTRICAL DIAGNOSTICS
ND
U0002–CAN C BUS OFF PERFORMANCE (340)
ND
BRAKES - ABS ELECTRICAL DIAGNOSTICS
5 - 217
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст