Dodge Dakota (ND). Manual — part 1207
3. Remove the upper C-pillar trim panel, refer to
(Refer to 23 - BODY/INTERIOR/PANEL-C PILLAR
UPPER TRIM - REMOVAL).
4. Using a trim stick C-4755 or equivalent, disengage
the retaining tabs that secure the lower C-pillar trim
panel (7) to the C-pillar (1).
5. Remove the screw (6) that secures the lower
anchor to the floor panel near the base of the C-pil-
lar.
6. Remove the seat belt (3) from the lower C-pillar
trim panel through the slots provided and remove
the trim panel.
INSTALLATION
Club Cab, Without Rear Jumper Seats
1. Position the lower C-pillar trim panel (4) to the
C-pillar and engage the retaining tabs that secure
the trim panel to the C-pillar.
2.
CAUTION: Keep the inner bottom end of the upper
C-pillar trim panel away from the cab back trim
panel when installing the upper C-pillar trim panel
to prevent scratching the back trim panel.Install
the upper C-pillar trim panel, (Refer to 23 - BODY/
INTERIOR/PANEL-C
PILLAR
UPPER
TRIM
-
INSTALLATION).
23 - 240
INTERIOR
ND
3. Install the rear door sill scuff plate, (Refer to 23 -
BODY/INTERIOR/PLATE-DOOR
SCUFF
-
INSTALLATION).
4. Install the outer front seat belt retractor cover,
(Refer to 23 - BODY/INTERIOR/COVER-OUTER
FRONT
SEAT
BELT
RETRACTOR
-
INSTALLATION).
ND
INTERIOR
23 - 241
Club Cab, With Rear Jumper Seats
1. Position the lower C-pillar trim panel (7) in the vehi-
cle.
2. Route the seat belt, lower anchor, latch plate and
turning loop (3) through the slots provided in the
lower C-pillar trim panel. Verify that the seat belt
webbing between the retractor and the lower
anchor is not twisted.
3. Position the seat belt lower anchor to the mounting
hole in the floor panel near the base of the C-pillar
and Install the screw (6) that secures the lower
anchor to the floor panel. Tighten the screw to 39
N·m (29 ft. lbs.).
4. Position the lower C-pillar trim panel to the C-pillar
(1) and engage the retaining tabs that secure the
trim panel to the C-pillar.
5.
CAUTION: Keep the inner bottom end of the upper
C-pillar trim panel away from the cab back trim
panel when installing the upper C-pillar trim panel
to prevent scratching the back trim panel.Install
the upper C-pillar trim panel, (Refer to 23 - BODY/
INTERIOR/PANEL-C
PILLAR
UPPER
TRIM
-
INSTALLATION).
6. Install the rear door sill scuff plate, (Refer to 23 -
BODY/INTERIOR/PLATE-DOOR
SCUFF
-
INSTALLATION).
23 - 242
INTERIOR
ND
7. Install the outer front seat belt retractor cover,
(Refer to 23 - BODY/INTERIOR/COVER-OUTER
FRONT
SEAT
BELT
RETRACTOR
-
INSTALLATION).
Quad Cab
1. Position the lower C-pillar trim panel (7) in the vehi-
cle.
2. Route the seat belt, lower anchor, latch plate and
turning loop (3) through the slots provided in the
lower C-pillar trim panel. Verify that the seat belt
webbing between the retractor and the lower
anchor is not twisted.
3. Position the seat belt lower anchor to the mounting
hole in the floor panel near the base of the C-pillar
and Install the screw (6) that secures the lower
anchor to the floor panel. Tighten the screw to 39
N·m (29 ft. lbs.).
4. Position the lower C-pillar trim panel to the C-pillar
(1) and engage the retaining tabs that secure the
trim panel to the C-pillar.
5. Install the upper C-pillar trim panel, (Refer to 23 -
BODY/INTERIOR/PANEL-C PILLAR UPPER TRIM
- INSTALLATION).
6. Install the rear seat, (Refer to 23 - BODY/SEATS/SEAT-SECOND ROW - INSTALLATION).
ND
INTERIOR
23 - 243
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст