Chrysler Le Baron, Dodge Dynasty, Plymouth Acclaim. Manual — part 20
Fig. 11 Rear Frame Dimensions—AP-Body
13 - 16
FRAME AND BUMPERS
Ä
CROSSMEMBER
REMOVAL (FIG. 12)
(1) Hoist vehicle and support on safety stands. Re-
fer to Group 0, Lubrication and Maintenance for
proper procedures.
(2) Remove front wheels.
(3) Disconnect lower ball joints from the knuckle
assembly. Refer to Group 2, Suspension for proper
procedures.
(4) Disconnect power steering hose tie-down from
rear upper edge of crossmember, if equipped.
(5) Remove bolts holding steering gear to cross-
member. Refer to Group 19, Steering for proper pro-
cedures.
(6) Remove bolt holding engine damper strut to
crossmember, if equipped with manual transaxle.
(7) Support crossmember on a suitable lifting de-
vice.
(8) Remove nuts holding rear of crossmember to
the frame.
(9) Remove bolts holding crossmember to frame
from above lower control arms.
(10) Separate the crossmember from the vehicle.
(11) Transfer lower control arms and sway elimi-
nator shaft to new crossmember, if crossmember is
being replaced. Refer to Group 2, Suspension for
proper procedure.
CROSSMEMBER INSTALLATION
Reverse the preceding operation.
Fig. 12 Crossmember
Ä
FRAME AND BUMPERS
13 - 17
FUEL SYSTEMS
CONTENTS
page
page
2.2L TURBO III MULTI-PORT FUEL INJECTION—
GENERAL DIAGNOSIS
. . . . . . . . . . . . . . . . . 95
2.2L TURBO III MULTI-PORT FUEL INJECTION—
ON-BOARD DIAGNOSTICS
. . . . . . . . . . . . . 100
2.2L TURBO III MULTI-PORT FUEL INJECTION—
SERVICE PROCEDURES
. . . . . . . . . . . . . . . 107
2.2L TURBO III MULTI-PORT FUEL INJECTION—
SYSTEM OPERATION
. . . . . . . . . . . . . . . . . . 83
2.2L/2.5L SINGLE POINT FUEL INJECTION—
GENERAL DIAGNOSIS
. . . . . . . . . . . . . . . . . . 35
2.2L/2.5L SINGLE POINT FUEL INJECTION—
ON-BOARD DIAGNOSTICS
. . . . . . . . . . . . . . 41
2.2L/2.5L SINGLE POINT FUEL INJECTION—
SERVICE PROCEDURES
. . . . . . . . . . . . . . . . 48
2.2L/2.5L SINGLE POINT FUEL INJECTION—
SYSTEM OPERATION
. . . . . . . . . . . . . . . . . . 24
2.5L FLEXIBLE FUEL MULTI-PORT FUEL
INJECTION—GENERAL DIAGNOSIS
. . . . . . . 66
2.5L FLEXIBLE FUEL MULTI-PORT FUEL
INJECTION—ON-BOARD DIAGNOSTICS
. . . 70
2.5L FLEXIBLE FUEL MULTI-PORT FUEL
INJECTION—SERVICE PROCEDURES
. . . . . 77
2.5L FLEXIBLE FUEL MULTI-PORT FUEL
INJECTION—SYSTEM OPERATION
. . . . . . . 55
3.0L MULTI-PORT FUEL INJECTION—
GENERAL DIAGNOSIS
. . . . . . . . . . . . . . . . . 125
3.0L MULTI-PORT FUEL INJECTION—
ON-BOARD DIAGNOSTICS
. . . . . . . . . . . . . 130
3.0L MULTI-PORT FUEL INJECTION—
SERVICE PROCEDURES
. . . . . . . . . . . . . . . 138
3.0L MULTI-PORT FUEL INJECTION—
SYSTEM OPERATION
. . . . . . . . . . . . . . . . . 113
3.3L AND 3.8L MULTI-PORT FUEL INJECTION—
GENERAL DIAGNOSIS
. . . . . . . . . . . . . . . . . 157
3.3L AND 3.8L MULTI-PORT FUEL INJECTION—
ON-BOARD DIAGNOSTICS
. . . . . . . . . . . . . 162
3.3L AND 3.8L MULTI-PORT FUEL INJECTION—
SERVICE PROCEDURES
. . . . . . . . . . . . . . . 169
3.3L AND 3.8L MULTI-PORT FUEL INJECTION—
SYSTEM OPERATION
. . . . . . . . . . . . . . . . . 145
ACCELERATOR PEDAL AND THROTTLE
CABLE
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
FUEL DELIVERY SYSTEM
. . . . . . . . . . . . . . . . . 3
FUEL TANKS
. . . . . . . . . . . . . . . . . . . . . . . . . . 14
GENERAL INFORMATION . . . . . . . . . . . . . . . . . . 1
SPECIFICATIONS
. . . . . . . . . . . . . . . . . . . . . . 178
GENERAL INFORMATION
Throughout this group, references are made to a
particular vehicle by letter designation. A chart
showing the breakdown of these designations is in-
cluded in the Introduction Section at the front of this
service manual.
The Fuel System consists of the fuel tank, fuel
pump, fuel filter, throttle body, fuel injectors, fuel
tubes and vacuum tubes.
The Fuel Delivery System consists of the fuel
pump, fuel filter, fuel lines and fuel hoses.
The Fuel Tank Assembly consists of the fuel tank,
filler tube, a fuel gauge sending unit assembly and a
pressure-vacuum filler cap.
Also, the Evaporation Control System is part of the
fuel system. The evaporation control system is de-
signed to reduce the emission of fuel vapor into the
atmosphere.
The description and function of the Evaporation
Control System is found in Group 25 of this manual.
FUEL REQUIREMENTS
Your vehicle was designed to meet all emission
regulations and provide excellent fuel economy when
using high quality unleaded gasoline.
VEHICLES WITHOUT TURBOCHARGED
ENGINES
Use unleaded gasoline having a minimum octane
rating of 87.
VEHICLES WITH TURBOCHARGED
ENGINES—EXCEPT 16 VALVE 2.2L ENGINES
These vehicles will operate satisfactorily on both
regular unleaded gasoline having a minimum octane
rating or 87, and premium unleaded gasoline having
a minimum octane rating of 91. The use of premium
unleaded gasoline will improve performance.
VEHICLES WITH 2.2L 16 VALVE ENGINES
The use of premium unleaded gasoline having a
minimum octane of 91 is recommended. If premium
unleaded is not available, then unleaded gasoline
Ä
FUEL SYSTEMS
14 - 1
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст