Chrysler Le Baron, Dodge Dynasty, Plymouth Acclaim. Manual — part 158
(4) Remove bolts holding hinge to hinge pillar and
separate hinge form vehicle.
FRONT DOOR HINGE INSTALLATION
Reverse the preceding operation. Align door to
achieve 6 mm (0.240 in.) gap to all surrounding pan-
els and flush across gaps.
OUTSIDE DOOR HANDLE
REMOVAL (FIG. 13)
(1) Remove door trim panel.
(2) Remove silencer pad and water shield as neces-
sary.
(3) Raise door glass to up position.
(4) Disconnect illuminated entry wire connector
from outside door handle assembly, if equipped.
(5) Disconnect latch release linkage from latch as-
sembly.
(6) Disconnect lock cylinder linkage from latch as-
sembly.
(7) Remove nuts holding outside handle bracket to
door panel and separate bracket from panel.
(8) Position linkage rods parallel to the back of
handle and remove handle assembly from door.
INSTALLATION
Reverse the preceding operation.
FRONT DOOR LATCH
REMOVAL (FIG. 14)
(1) Remove door trim panel.
(2) Remove silencer pad and water shield as neces-
sary.
(3) Disconnect linkage rods from door latch assem-
bly.
(4) Remove screws holding latch door end frame.
(5) Separate latch from door.
INSTALLATION
Reverse the preceding operation.
FRONT DOOR WINDOW REGULATOR
REMOVAL (FIG. 15 OR 16)
MANUAL OR ELECTRIC
(1) Remove front door trim panel.
(2) Remove silencer pad and water shield.
(3) Remove side view mirror trim cover and door
frame trim moulding.
Fig. 12 Front Door Assembly
Fig. 13 Front Door Handle Assembly
Fig. 14 Front Door Latch Assembly
23 - 42
AC-BODY
Ä
(4) Remove door glass.
(5) Remove nut holding cable retainer to inner
door panel and slip cables from behind retainer.
(6) Disengage push in retainer holding cables to
inner door panel above speaker on vehicles with
power windows.
(7) Remove bolts holding top of glass lift bar to in-
ner door panel.
(8) Remove nut holding bottom of lift bar to bot-
tom panel of door.
(9) Remove bolts holding window crank regulator
to inner door panel on vehicles with manual win-
dows. Remove nuts holding motor and regulator to
inner door panel on vehicles with power windows.
(10) Separate window regulator from vehicle.
INSTALLATION
Reverse the preceding operation.
FRONT DOOR GLASS
REMOVAL
(1) Remove front door trim panel.
(2) Remove silencer pad and water shield.
(3) Remove side view mirror trim cover and door
frame trim moulding.
(4) Remove front door speaker.
(5) Move glass to the down position and remove
glass to lift plate fasteners.
(6) Loosen door glass slam bumpers.
(7) Lift glass upward through opening at top of
door.
INSTALLATION
Reverse the preceding operation.
REAR DOOR TRIM PANEL
REMOVAL (FIG. 17)
(1) Disengage retaining clips holding padded insert
assembly to door panel.
(2) Remove courtesy lamp lens.
(3) Remove screws holding arm rest to door panel.
(4) Remove screws at forward edge of trim panel.
(5) Remove hidden screws from carpet insert on
lower trim panel.
(6) Remove screw and disengage clips holding
switch bezel to door trim panel.
(7) Disengage frog-leg fasteners holding trim panel
to door and disconnect courtesy lamp wire connector.
INSTALLATION
Reverse the preceding operation.
REAR DOOR FRAME TRIM MOULDING
TRIM MOULDING REMOVAL (FIG. 17)
(1) Remove rear door trim panel.
(2) Disengage trim clips holding trim moulding to
door frame.
(3) Separate trim moulding from door frame.
TRIM MOULDING INSTALLATION
Reverse the preceding operation.
REAR DOOR SILENCER AND WATER SHIELD
REAR DOOR WATER SHIELD REMOVAL
(1) Remove door trim panel.
(2) Pull water shield from adhesive around perim-
eter of door inner panel.
Fig. 15 Front Door Manual Window Regulator
Fig. 16 Front Door Power Window Regulator
Ä
AC-BODY
23 - 43
REAR DOOR SILENCER AND WATER SHIELD
INSTALLATION
Reverse the preceding operation.
REAR DOOR AND HINGE
The rear door hinge is welded to the door and
bolted to the B-pillar. The door half of the hinge piv-
ots on a removable hinge pin. The hinge pin is
driven in from the bottom on the top hinge and from
the top on the bottom hinge. All adjustments to the
hinge are performed on the hinge pillar half of the
hinge. If the welded half of the hinge must be bent to
align door, consult an authorized body repair facility.
REAR DOOR REMOVAL (FIG. 18)
(1) Remove B-pillar trim panel and disconnect all
wire connectors leading to door. Push wire harness
through access hole in B-pillar into hinge opening.
(2) Support door on a suitable lifting device.
(3) Drive bottom hinge pin upward and remove pin
from hinge.
(4) Drive top hinge pin downward and remove pin
from hinge.
(5) Separate door from vehicle.
REAR DOOR INSTALLATION
Reverse the preceding operation. The door should
not require re-alignment. If door does need align-
ment, refer to Rear Door Hinge Installation para-
graph in this section.
REAR DOOR HINGE REMOVAL (FIG. 18)
(1) To remove upper hinge bolted half, remove
B-pillar trim panel. To remove lower hinge bolted
half it is not necessary to remove B-pillar trim.
(2) Support rear door on a suitable lifting device.
(3) Drive out hinge pin on the effected hinge.
(4) Remove bolts holding hinge to B-pillar and sep-
arate hinge form vehicle.
REAR DOOR HINGE INSTALLATION
Reverse the preceding operation. Align door to
achieve 6 mm (0.240 in.) gap to all surrounding pan-
els and flush across gaps.
REAR DOOR OUTSIDE HANDLE
REMOVAL
(1) Remove rear door trim panel.
(2) Remove silencer pad and water shield as neces-
sary.
(3) Disconnect latch release linkage rod from door
latch.
(4) Remove nuts holding handle bracket to inner
door panel.
(5) Separate outside door handle from door.
INSTALLATION
Reverse the preceding operation.
REAR DOOR LATCH
REMOVAL
(1) Remove rear door trim panel.
(2) Remove silencer pad and water shield as neces-
sary.
(3) Disconnect linkage rods from door latch.
(4) Remove screws holding latch to door end frame.
(5) Separate latch from rear door.
INSTALLATION
Reverse the preceding operation.
Fig. 17 Rear Door Trim Panel
Fig. 18 Rear Door Assembly—Typical
23 - 44
AC-BODY
Ä
REAR DOOR GLASS
REMOVAL (FIG. 19)
(1) Remove rear door trim panel.
(2) Remove silencer pad and water shield.
(3) Remove door frame trim moulding.
(4) Remove screws holding lift plate to door glass.
(5) Loosen glass slam bumpers.
(6) Lift glass upward through opening at top of
door.
INSTALLATION
Reverse the preceding operation.
REAR DOOR WINDOW REGULATOR
REMOVAL
(1) Remove rear door trim panel.
(2) Remove silencer pad and water shield.
(3) Remove bolts holding regulator to inner door
panel.
(4) Slide regulator lift arm roller from lift plate
channel.
(5) Separate regulator from door.
INSTALLATION
Reverse the preceding operation.
REAR DOOR GLASS LIFT PLATE AND GUIDE BAR
REMOVAL
(1) Remove rear door glass.
(2) Remove bolts holding upper guide bar mount
bracket to inner door panel.
(3) Remove nut holding guide bar to lower door
bottom frame.
(4) Slide lift plate channel from regulator roller.
(5) Separate guide bar from door.
INSTALLATION
Reverse the preceding operation.
OVERHEAD CONSOLE
REMOVAL (FIG. 20)
(1) Remove screws holding overhead console to re-
inforcement bracket.
(2) Slide overhead console rearward to separate re-
inforcement bracket retainer tab from console.
(3) Lower console from roof and disconnect wire
connectors.
INSTALLATION
Reverse The preceding operation.
HEAD LINING
REMOVAL (FIG. 21)
(1) Disconnect battery negative cable.
(2) Pull dome lamp downward to disengage from
retaining ring in head lining. Separate lens from
lamp body and remove bulb. Separate bulb holder
from lamp body. Remove attaching screw holding re-
taining ring to roof bow.
(3) Remove screws holding coat hooks to roof above
rear doors.
(4) Remove roof rail and A-pillar mouldings.
(5) Remove screws holding sun visors to roof
header and disconnect wire connector, if equipped.
Remove inboard sun visor hangers.
(6) Remove overhead console, if equipped.
Fig. 19 Rear Door
Fig. 20 Overhead Console
Ä
AC-BODY
23 - 45
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст