Dodge Durango (HB). Manual — part 1376
![](/vehicles/wlang/dowa/jaicchinds/knsp.png)
INSTALLATION
1. Install the hinge (2), slide back into position on the
fender rail and align all marks.
2. From inside the fender, install the two hinge bolts
(1).
3. Tighten the rear bolt to 20 N·m (15 ft. lbs.)
4. Tighten the front bolt to 20 N·m (15 ft. lbs.)
5. Install the nuts attaching the hinge to the hood and
tighten the nuts to 23 N·m (17 ft. lbs.)
6. Install the fender support bolt and tighten to 8 N·m
(75 in. lbs.).
7. Install the cowl grille. (Refer to 23 - BODY/EXTE-
RIOR/COWL GRILLE AND SCREEN - INSTALLA-
TION)
8. Install the wheelhouse splash shield and install the
rivets. (Refer to 23 - BODY/EXTERIOR/FRONT
WHEELHOUSE SPLASH SHIELD - DESCRIP-
TION)
9. Check hood fit and adjust if required. (Refer to 23 -
BODY/BODY STRUCTURE/GAP AND FLUSH -
SPECIFICATIONS)
HOOD
REMOVAL
1. Open hood and disconnect the washer hoses.
2. Mark all nut and hinge attachment locations using
a grease pencil or equivalent, to provide reference
marks for installation.
3. Remove the top nuts (3) attaching hood to hinge
and loosen the bottom nuts (3) until they can be
removed by hand.
4. Remove the bottom nuts (3) and separate the hood
(1) from the vehicle.
HB
HOOD
23 - 17
![](/vehicles/wlang/dowa/jaicchinds/heis.png)
INSTALLATION
1. Position the hood (1) onto the hinges (2).
2. Align all marks and install the nuts.
3. Tighten the nuts too 23 N·m (17 ft. lbs.).
4. Connect the washer hoses.
5. Close hood and adjust as necessary. (Refer to 23 -
BODY/HOOD/HOOD - ADJUSTMENTS)
ADJUSTMENTS
NOTE: For gap and flush specifications, (Refer to
23 - BODY/BODY STRUCTURE/GAP AND FLUSH -
SPECIFICATIONS).
1. If hood is low in relation to cowl panel, loosen the
hood to hinge nuts and insert shims between hinge
and hood.
2. Adjust hood bumpers (2) in or out to adjust hood-
to-fender height alignment.
3. Loosen the hood latch screws.
4. Close the hood and check the fore/aft position of
the hood.
5. Loosen the hood to hinge nuts to adjust the fore/aft
position.
6. Once the fore/aft position of the hood is correct,
tighten the hood to hinge nuts to 23 N·m (17 ft. lbs.).
7. Lower the hood. Inspect clearance between the hood and the cowl cover.
8. Adjust the hood latch as necessary and tighten the bolts to 11 N·m (8 ft. lbs.).
9. Align the latch striker so that striker enters the latch squarely and without binding.
23 - 18
HOOD
HB
![](/vehicles/wlang/dowa/jaicchinds/hynd.png)
LATCH
REMOVAL
1. Remove the push pin fasteners and remove the
upper radiator shroud.
2. Using a grease pencil or equivalent, mark latch
position for installation alignment.
3. Remove bolts (3) attaching hood latch (4) to upper
radiator crossmember (1).
4. Separate hood latch (1) from crossmember and
disconnect the release cable (2).
INSTALLATION
1. Connect release cable (2) to the hood latch (1).
HB
HOOD
23 - 19
![](/vehicles/wlang/dowa/jaicchinds/hauce.png)
2. Install the latch (4) lining up the marks made pre-
viously and install the bolts (3).
3. Tighten the bolts to 11 N·m (8 ft. lbs.).
4. Close hood and adjust latch as necessary. (Refer
to 23 - BODY/HOOD/LATCH - ADJUSTMENTS)
ADJUSTMENTS
1. Check and adjust the hood if required. (Refer to 23
- BODY/HOOD/HOOD - ADJUSTMENTS)
2. Remove the push pin fasteners and remove the
upper radiator shroud.
3. Loosen the hood latch bolts (3).
4. Move the latch to the correct location and lightly
tighten the bolts.
5. Close the hood slowly and observe the latching
operation.
6. If necessary, adjust the latch position and tighten
the bolts to 11 N·m (8 ft. lbs.).
RELEASE-HOOD LATCH
REMOVAL
1. Remove the grille. (Refer to 23 - BODY/EXTERI-
OR/GRILLE - REMOVAL)
2. Remove hood latch (4). (Refer to 23 - BODY/
HOOD/LATCH - REMOVAL)
3. Remove the left headlamp unit. (Refer to 8 - ELEC-
TRICAL/LAMPS/LIGHTING
-
EXTERIOR/HEAD-
LAMP UNIT - REMOVAL)
4. Remove the plastic rivets and remove the left front
wheelhouse splash shield. (Refer to 23 - BODY/
EXTERIOR/FRONT
WHEELHOUSE
SPLASH
SHIELD - DESCRIPTION)
5. Detach the release cable and the retainer clips (2)
in the engine compartment.
23 - 20
HOOD
HB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст