Dodge Durango (HB). Manual — part 1377
6. Separate the release cable grommet from the dash
panel hole.
7. Detach the release cable and the retainer clips (4).
8. From the inside of the vehicle, remove the screws
(5) attaching the hood release handle (2) to the
bottom of the instrument panel (1).
9. Pull/route the hood release cable through the dash
panel hole and remove it from the inside of the
vehicle.
INSTALLATION
NOTE: If replacement hood latch is also being
installed, ensure that it is thoroughly lubricated.
1. From inside the vehicle, pull/route the hood release
cable through the dash panel hole and into the
engine compartment.
2. Install the hood release handle (2) and install the
screws (5).
3. Install the cable grommet in the dash panel hole.
4. Attach the retainer clip (4) to the release cable and
install.
5. Attach the retainer clips (2) to the release cable
and install them into the holes in the engine com-
partment.
6. Install hood latch. (Refer to 23 - BODY/HOOD/
LATCH - INSTALLATION)
7. Install the wheelhouse splash shield and install the rivets. (Refer to 23 - BODY/EXTERIOR/FRONT WHEEL-
HOUSE SPLASH SHIELD - DESCRIPTION)
8. Install the left headlamp unit. (Refer to 8 - ELECTRICAL/LAMPS/LIGHTING - EXTERIOR/HEADLAMP UNIT -
INSTALLATION)
9. Install the grille. (Refer to 23 - BODY/EXTERIOR/GRILLE - INSTALLATION)
HB
HOOD
23 - 21
DOOR - FRONT
TABLE OF CONTENTS
page
page
PANEL-TRIM
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
. . . . . . . . . . . . . . . . . . . . . . . . . 23
WATERSHIELD
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
. . . . . . . . . . . . . . . . . . . . . . . . . 24
GLASS
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
. . . . . . . . . . . . . . . . . . . . . . . . . 25
REGULATOR-WINDOW
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
. . . . . . . . . . . . . . . . . . . . . . . . . 27
HANDLE-EXTERIOR
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
. . . . . . . . . . . . . . . . . . . . . . . . . 29
CYLINDER-LOCK
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
. . . . . . . . . . . . . . . . . . . . . . . . . 31
CHANNEL-GLASS
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
. . . . . . . . . . . . . . . . . . . . . . . . . 32
LATCH
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
. . . . . . . . . . . . . . . . . . . . . . . . . 34
. . . . . . . . . . . . . . . . . . . . . . . . 35
DOOR
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
. . . . . . . . . . . . . . . . . . . . . . . . . 36
. . . . . . . . . . . . . . . . . . . . . . . . 36
HINGE
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
. . . . . . . . . . . . . . . . . . . . . . . . . 41
STRIKER
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
. . . . . . . . . . . . . . . . . . . . . . . . . 42
. . . . . . . . . . . . . . . . . . . . . . . . 43
PANEL-TRIM
REMOVAL
1. Remove the screws (5 & 7).
CAUTION: Trim panel is attached to the door using
hooks molded into the panel. Do not pull the trim
panel straight off or damage to the panel and/or
power switch assembly may occur.
2. Lift the trim panel up off the lock rod (4) and
attachment hooks and separate the panel from the
door slightly.
3. Disconnect the electrical connectors (1).
4. Disconnect the inside handle actuator rod (3) and
remove the trim panel (6).
23 - 22
DOOR - FRONT
HB
5. Remove the switch panel (1) if necessary.
INSTALLATION
1. Install the switch assembly (1).
2. Position the trim panel (6) and connect the inside
handle actuator rod (3).
3. Connect the electrical connectors (1).
4. Lift the trim panel up and onto the lock rod (4) and
attachment hooks.
5. Install the screws (5 & 7).
HB
DOOR - FRONT
23 - 23
WATERSHIELD
REMOVAL
CAUTION: Do not allow the watershield or adhe-
sive to become contaminated with dirt or other
foreign substances.
Do not damage the watershield during removal
and installation.
If the watershield becomes contaminated or dam-
aged, replace the watershield.
1. Remove the speaker. (Refer to 8 - ELECTRICAL/
AUDIO/SPEAKER - REMOVAL)
2. Remove the door trim panel. (Refer to 23 - BODY/
DOOR - FRONT/TRIM PANEL - REMOVAL)
3. Separate the watershield (1) from the inner door
panel (2) and off of the latch linkages.
INSTALLATION
CAUTION: Do not allow the watershield or adhe-
sive to become contaminated with dirt or other
foreign substances.
Do not damage the watershield during removal
and installation.
If the watershield becomes contaminated or dam-
aged, replace the watershield.
1. Position
the
wire
harness
and
actuator
rods
through the holes in the watershield.
2. Secure the watershield to the inner door panel.
3. Install the speaker. (Refer to 8 - ELECTRICAL/AU-
DIO/SPEAKER - INSTALLATION)
4. Install the trim panel. (Refer to 23 - BODY/DOOR -
FRONT/TRIM PANEL - INSTALLATION)
23 - 24
DOOR - FRONT
HB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст